搜索资源列表
RSSIRange
- Received Signal Strength Indicator in PIC24 with wireless communication. Ping a char and add RSSI information to the message.
timers
- Timer This example application demonstrates the use of the timers to generate periodic interrupts. One timer is set up to interrupt once per second and the other to interrupt twice per second each interrupt handler will toggle its own indi
interrupt
- 在arm2440上按下按键，产生中断，处理led指示灯的状态-In arm2440 press the button and generate an interrupt to handle led status indicator
GPIO_INT
- 程序正常运行时，熄灭LED指示灯 当按键按下时·触发中断，点亮LED指示灯。按键放开后 又熄灭LED指示灯-Program during normal operation, off LED indicator when the button is pressed interrupt, lit LED lights. LED indicator light turns off after button release
YLP2440
- 1.1 YLP2440开发板简介 YLP2440开发板硬件资源: 中央处理器 ── CPU: Samsung S3C2440A，主频400MHz； 外部存储器 ── SDRAM：64MB； ── NAND Flash：64MB（K9F1208，用户可自己更换为16M、32M或128M的NandFlash） 串口 ── 两个五线异步串行口，波特率高达115200bps； 网络接口 ── 一个10M/100M网口，采用DM9000AEP，带联接和传输指示灯；-1.1 YLP2440 Developm
KERYLED
- 用LPC2124做的一个按键显示灯,是初学ARM7的好帮手例程,同时里面还有PROTEUS的效果仿真.-To do with the LPC2124, a key indicator is a good helper routines beginner ARM7, while there is also the effect of PROTEUS simulation.
2-key-recognition-and-LED-indicator
- 硬件环境： 按键：Key1--PD2 Key2--PD3 （低电平表示有按键按下） LED：LED1~LED8--PC0~PC7； （LED在高电平被点亮） 功能：当Key1按下时，所有8个LED的均被点亮 当Key2按下时，所有8个LED均被熄灭-Hardware environment: Key: Key1-PD2 Key2-PD3 (low level said keys pressed) LED: LED1 ~ LED8-PC0 ~ PC7 (L
102-DS1302
- DS1302 Trickle Charge Timekeeping Chip-The DS1302 Trickle Charge Timekeeping Chip contains a real time clock/calendar and 31 bytes of static RAM. It communicates with a microprocessor via a simple serial interface. The real time clock/calendar
code.lpc23xx.peripherals.iar
- 接通电源后开发板左下角电源指示灯亮，表示电源工作正常。这里是LPC2468开发板全部例程,keil开发环境，希望对新人有帮助。-After turning on the power development board of the lower left corner of the power indicator light, said the power supply works. Here is the LPC2468 development board all the routines, a
Test-4011
- 入门级DSPIC30F4011测试程序，自己构建DSPIC30F4011的最小系统电路，只使用一个LED作为指示，让LED显示，测试系统是否工作。然后添加一些需要的测试内容，让开发工作开展下去。测试OK.-The minimum system circuit of DSPIC30F4011, using only one LED as indicator, let LED display, test system is working. Then add some test content, d
LPMA
- Low power, loop powered miliamperes indicator using 2 1/2 seven segment LCD display and STM32L053. Circuit and keil C code include.
EKL4
- 故障指示器绝对原创程序，在市场改革上销售行情不错的，大家啊来拿巴！-Fault Indicator absolutely original program, sales prices in the market reform is good, we ah come and collect bar!
TIM-timer-PWM-brightness-control
- TIM定时器PWM控制指示灯亮度,包含库函数，是STM32F107VC程序，已经编辑调试通过，可以直接使用-TIM timer PWM brightness control indicator, including library functions is STM32F107VC program debugging has been edited, you can directly use
Tracker_V2.03
- High voltage electricity use, short-circuit fault indicator! Sensor plus display instrument procedures
pr851
- Analysis of the signal time domain, frequency domain, cepstrum, cyclic spectrum, etc. GSM is GMSK modulation signal generation, Chaos indicator for Lyapunov index calculation.
xrajs
- Using weighted model nodes in the network strength and weight are power law distribution, Independent component analysis algorithm reduces the raw data noise, Chaos indicator for Lyapunov index calculation.
aarmg
- Fiber Transmission wireless communication system performance, Chaos indicator for Lyapunov index calculation, Has been successful debugging. M contains files can be directly run.
ax048
- Chaos indicator for Lyapunov index calculation, Car class-based truck driver trying to Matlab program, It comprises aircraft flight attitude control, such as slip angle, tilt angle, roll angle, pitch angle.
wd250
- Chaos indicator for Lyapunov index calculation, Based on wavelet transform digital watermarking algorithm matlab code, For feature extraction, signal de-noising.
vebak
- Chaos indicator for Lyapunov index calculation, Verification is available, Using weighted model nodes in the network strength and weight are power law distribution.