搜索资源列表
ARM的ADC
- 使用AIN0和AIN1测量两路直流电压，并将结果通过UART0想PC机发送。-compute and the use of two-way con measuring DC voltage, the results through UART0 sent to PC.
ch452
- CH452按键和显示板驱动程序,采用级联方式,模拟SPI口一次发送24位数据.每级120个灯和120个按键.采用查表换算.-CH452 keys and display drivers, concatenation, a simulation of SPI I sent 24 data. Each level 120 lights and 120 keys. Using Lookup conversion.
winCEtouchdrive
- The touch screen driver reads input from touch screen hardware and converts it to touch events that are sent to the input system. The driver is also responsible for converting uncalibrated coordinates-The touch screen reads input from driver to uch s
cat24wc02LED
- 这是Small RTOS 51 在DP－51下载仿真实验仪上使用CAT24WC02驱动程序的例子。本例程序按照相应的的通讯协议接收一个数据，并将接收到的数据显示到LED数码显示器上。然后将接收到的数据写入Cat24Wc02中，再在同一位置将数据读出，并将读出的数据通过串口发送回来。通讯协议参考rtos随想曲和test.ini。 注意:(1)在KEIL C51 工程中,我已经把输出文件目录设在e:\\temp中,您可以在Project->Options for Target \"T
rxdemo
- mc13213无线串口接受并发送到超级终端的元代码-mc13213 Wireless Serial accepted and sent to the Super Terminal yuan code
aduart
- MC13213接受AD采集信号并发送到串口进行接受的程序，-MC13213 accept AD Acquisition signal sent to the serial accept the procedure,
BTHostV1.43
- 蓝牙协议HCI层指令发送,主要用于测试HCI以下的代码及RF部分测试.-HCI layer Bluetooth protocol directives sent, mainly for testing the following code HCI and RF some of the test.
STM32f103-ADC-USART.rar
- STM32f103两路ADC数据采集用USART送出,STM32f103 two ADC data acquisition sent by USART
nrf24l01
- 基于ARM的nrf24l01芯片发送接收程序。按键发送数据，另一端接受后发送至串口显示在电脑端。-ARM-based chips nrf24l01 send and receive process. Button to send data received and sent to the other end of the serial displayed on the computer side.
STM32_USART1
- stm32 库文件：3.10 本程序是使用UART1接收中断,收到数据后直接把原数据从USART1发回去 一开机时,会发送 "Starting....."到USART1-stm32 Library: 3.10 This procedure is to use UART1 receive interrupt, received data directly to the original data sent back from USART1 A start,
STM32f103-ADC-USART
- STMicroelectronics 32 用ADC模块采集两路信号并通过USART模块送出 * 设置ADC1的常规转换序列包含CH10和CH16(片内温度传感器） * 设置了连续转换模式，并使用DMA传输-STMicroelectronics 32 ADC module with the acquisition of two signals sent through the USART module* set ADC1 conventional conversion sequence
CAN
- MC9S12单片机 CAN总线初始化及数据发送-Single-chip CAN bus MC9S12 initialization and data sent
LT-ARM214X-UDP
- lpc2148的udp数据采集程序，模块28j60，采集后发送到串口-lpc2148 of the the udp data acquisition program, module 28j60 after collection is sent to the serial port
ourdev_526496
- 个简单的以太网发送速度测试程序，发送的数据是一个固定的UDP报文，循环反复发送，实测PC端网卡占用率 96％，也就是在 96Mbps 左右！-A simple test procedure speed Ethernet sending, sending the data is a fixed UDP packets sent repeatedly cycle, the measured end PC card 96 occupancy rate, which is about the 96Mb
51-send-chinese-to-PC
- 51向电脑发送汉字 串口发送汉字 单片机发送汉字-51 characters sent to the computer serial port to send Chinese characters SCM
SoftIIc
- 软件IIC,单片机用软件IIC驱动程序是打发多少-Software IIC, Singlechip IIC driver software is the number sent
Ethernet
- lpc2468以太网驱动，使用tinystack协议栈，实现基本的协议报发送，Keil开发环境-lpc2468 Ethernet driver, use tinystack protocol stack to achieve the basic agreement reportedly sent, Keil development environment
ARM7_LPC21xx_SPI2
- LPC21xx ARM7 SPI 内置ADC使用串口发送-LPC21xx ARM7 SPI serial sent using built-ADC
communications
- vb与arm通信，在PC机上利用VB6.0开发串口通信界面，把access数据库中的数据传送到ARM开发版的flash中-vb and communications arm, in the PC, using VB6.0 to develop serial communication interface, to access the data in the database sent to the ARM version of the flash in the development of
ARM2410
- 实现查询方式串口的收发功能。接收来自串口（通过超级终端）的字符并将接收到的 字符发送到超级终端-Implementation of the transceiver serial port query functions. Receive from the serial port (via HyperTerminal) characters and will receive the characters sent to HyperTerminal