搜索资源列表
seriseprogram
- 两块51单片机通过串口相互通信 其中有握手协议-2 through 51 microcontroller serial communications including mutual handshake protocol
vbpc
- 在Windows98下利用VB的串行通讯控件可实现PC机与多单片机之间的通讯。采用定时器控制大大加快了自动化进程，克服了往多“握手”协议造成的通讯速度缓慢的缺点。本文以PS1016单片机为例，详细介绍了PC机与单片机之间的串行通讯、数据的发送和接收。 -in Windows98 using VB serial communication controller can be achieved with a PC between the MCU communications. Using the t
VB-PC-and-multi-microcontroller-communications
- 在Windows98下利用VB的串行通讯控件可实现PC机与多单片机之间的通讯。采用定时器控制大大加快了自动化进程，克服了往多“握手”协议造成的通讯速度缓慢的缺点。-in Windows98 using VB serial communication controller can be achieved with a PC between the MCU communications. Using the timer control greatly accelerate the automatio
look1
- look1為電子看板的第二個芯片，使用自制的握手信號與look通訊，可以進行數據傳送，以及控制16個數碼管顯示，此案例已成功用於生產現志，所用的元件很少，功能較大呢-electronic Kanban look1 the second chip, the use of home-made look handshake signals and communications, data transmission can be carried out, as well as control of 16
speedstacks
- 握手起跑器:当用户双手同时握住产品时,起跑器开始工作,LCD显示.MCU:NTK-起跑器handshake: When a user hold hands at the same time product,起跑器start working, LCD display. MCU: NTK
handshake
- 利用多模式调制解调器芯片CMX868能直接通过高速串行总线与单片机串行接口进行通信这一特点设计的一套采用单片机来控制CMX868芯片的数据传输系统，握手协议部分-The use of multi-mode modem chip CMX868 directly by high-speed serial bus and the microcontroller serial interface to communicate with this feature set designed to use m
c
- 利用51单片机控制PTR6000无线传输模块实现远程控制，包括发送和接收部分的握手协议等完全版资料，适当改动即可应用-51 SCM control PTR6000 using wireless transmission module for remote control, handshake agreements, including the full version information, appropriate changes to be applied
JZ863SHUANGJIONGXIN
- 单片机通过JZ863，完成双击串行通信，含握手和通信过程.2010-11-02，xowalee。-MCU through JZ863, complete double-click the serial communications, including handshake and communication process .2010-11-02, xowalee.
GPIB_Sample_For_PIC_By_C
- PIC单片机应用之一，利用RB端口做控制信好线号和交握信号线，RD端口作为数据信号线，简单模拟GPIB控制器，实现对其他仪器设备的操控。同时以RC1/2输出作为GPIB动作状态指示灯（ACK/LSN）。 注：C语言编辑-One PIC microcontroller applications About GPIB, Using RB port as Control and handshake signal Line and RD Port as data line and RC1/2 as
USART_test
- STM32F103ZE单片机串行通讯程序，包括握手信号、命令字、数据校验和以及发送接收是否成功标志。已经在开发板上调试成功，可以放心使用。-STM32F103ZE microcontroller serial communication program, including handshake signals, the command word, and sending and receiving data validation, and the success flag. Has been s
hongwaicewen
- 基于51单片机和红外测温传感器的测温程序，实现双机握手传输和液晶显示-51 And the infrared temperature sensor temperature measurement program to achieve the dual handshake transmission and LCD
serialcomproteus
- 串口通信，proteus仿真，带显示，包括三次握手和简单传输两种模式，-Serial communication proteus simulation, with display, including the three-way handshake and the simple transfer of two modes,
commucination
- 51单片机 多机通信 例程， 写的很经典，别人写的，感觉不错 就分享一下，完整的握手协议，思路可以参考一下。-51 single-chip multi-machine communication routines, written in a very classic, written by someone else, I feel good on the share, the full handshake protocol, ideas can reference.
prg2051
- Using this programmer you can program the internal flash of the microcontroller AT89C2051 from Atmel. The AT89C2051 programmer is connected via the serial RS232 interface to a PC. In comparison with other programmers, you do not need a special softw
i2c
- stc12c5a60s2单片机，I2C接口通讯程序，可实现I2C总线的启动，停止及握手等功能-stc12c5a60s2 microcontroller, I2C interface communication program, can be realized starting I2C bus stop and other functions handshake
stc-isp-v4.80-not-setup
- STC单片机ISP烧写软件4.48版本对于老些型号的STC芯片可能有用，握手协议等-STC microcontroller ISP programming software version 4.48 may be useful for some older models of the STC chip handshake protocol
spi-for-fpga-and-stm32
- ＦＰＧＡ于ＳＴＭ３２握手ＳＰＩ通信，ＤＡＣ数据的传输，双向的数据传输-FPGA Handshake SPI communication to STM32
串口接受数据
- 51单片机串口接受数据，需要有握手包或者帧头，ECO或者结束符(51 single-chip serial port to receive data, you need to have a handshake package or frame header, ECO or terminator)