搜索资源列表
shuangjitongxin
- 单片机实现双机通信的汇编语言程序! 汇编语言实现-MCU-machine communication procedures assembly language! Language Series
instrument_amplifier
- 这是我设计制作的仪表放大器的一个单片机程序。采用C51系列单片机，Keil软件开发环境，用C语言开发，具有液晶显示功能和简单的人机交互界面，主要是用来控制放大器的放大倍数，以满足不同的量程范围。-This is my design of an instrumentation amplifier SCM procedures. Using C51 series microcontroller, Keil software development environment with C-languag
C51Washer
- Keil uVision2下用C语言开发的洗衣机嵌入式系统代码-Keil uVision2 using C language development of the washing machine code embedded system
doujang
- 单一的豆浆机的控制器的汇编语言程序源代码-single Soymilk Machine Controller of the assembly language source code
inverter
- 这是台达M系列变频器的主板机器码反汇编后的汇编语言源程序。编译后可直接烧写。-This is the Delta M series inverter board disassembled machine code assembly language source code. Compiled directly programmed.
twi
- C语言实现的基于AVR 8位单片机的TWI通讯！ 通过中断服务程序中的状态机，与TWI硬件状态机相配合，实现快速准确的数据交换！-C language based on the AVR 8-bit MCU s TWI communication! Through the interrupt service routine of the state machine, with the TWI hardware state machine matched the achievement of r
proteusofwaterheater
- proteus热水器仿真，包含电路硬件图及汇编语言，并在keil2中源代码通过-Proteus water simulation, including the hardware circuit diagram and assembly language, and in the source code through keil2
FM_BPSK
- Send_message 数字发信机测试函数模块 功能：DDS语言调频发信机，中心载波频率可在2MHz ~ 10MHz之间任意切换， 显示当时刻载波中心频率；-The number of letters Send_message test function modules: DDS machine language FM sent a letter, the center carrier frequency 2MHz ~ 10MHz can switch back and forth b
mcs51huibianchengxu
- 汇编语言是面向机器硬件的语言，要求程序设计者 对MCS-51单片机具有很好“软、硬结合”功底。 介绍程序设计的基本知识及如何使用汇编语言来进 行基本的程序设计。 5.1 汇编语言程序设计概述 5.1.1 机器语言、汇编语言和高级语言-Assembly language is machine-oriented hardware language, ordering procedures for MCS-51 microcontroller designers have g
Ultrasonic_Ranging
- 基于弹片机的超声波测距C语言程序；使用单片机的3.2口发送；3.5口接收-Based on Ultrasonic Ranging C shrapnel machine language program the use of SCM 3.2 to send 3.5 receiver
stil_file_antomy
- 用于机台测试的STIL语言的详细语法描述-STIL test for the machine language syntax described in detail
C-language-courses_vending-machine
- C语言课程设计 模拟自动售货机 运行在TC界面下-The C language courses designed to simulate a vending machine to run in the TC interface
Dual-machine-communications
- 双机通讯功能的设计，用51单片机，c语言编写，要实现这功能，必须要两个板进行通信 只要把，两个板的10和11脚对调接就行-Dual communication design, with 51, c language, to achieve this functionality, we must communicate as long as the two plates, two plates 10 and 11 feet on the line swap meet
two-machine-communication
- 双机通信，该程序为51单片机的c语言程序 ，编写了关于两个单片机接收和发送的程序，并且已存在烧写程序。-Two-machine communication, the program for 51 MCU c language program, written on two single-chip receive and transmit procedures and programming procedures already exist.
Driving-a-stepper-machine
- 该程序是用C语言编写，在keil软件中编译通过。通过该程序，可以了解步进机工作的基本原理，当然，如果您希望步进机按照您所想的方式进行工作，您可以对该程序进行修改-The program is written in C language in keil software compiled through. With this program, you can understand the basic principles of the stepper machine work, of course
The-state-machine
- 单片机的万能语言就是状态机，从常用的2种状态机编写方式展开介绍-SCM is the universal language state machine, from the commonly used two kinds of ways to start to write state machine introduced
interpret
- MS-51单片机的中断示例程序，采用汇编语言编写。当中断到来的时刻，相应引脚控制的LED灯状态反转。-Program of Machine language was written for MS-51 to realize the function of interpret. When the signal of interpret comes, LED connecting with the pin will reverse.
MCU-C-language-tutorial
- 在众多单片机中51 架构的芯片风行 很久，学习资料也相对很多，是初学的较好的选择之一。51 的编程语言常用的有二种，一 种是汇编语言，一种是C 语言。汇编语言的机器代码生成效率很高但可读性却并不强，复 杂一点的程序就更是难读懂，而C 语言在大多数情况下其机器代码生成效率和汇编语言相 当，但可读性和可移植性却远远超过汇编语言，而且C 语言还可以嵌入汇编来解决高时效 性的代码编写问题。对于开发周期来说，中大型的软件编写用C 语言的开发周期通常要小 于汇编语言很多。-In ma
vending-machine-C51-CODE
- 课程设计的自动售货机源代码，用51单片机做的，使用C语言编写-课程设计的自动售货机源代码，用51单片机做的，使用C语言编写 课程设计的自动售货机源代码，用51单片机做的，使用C语言编写 Course design of the vending machine source code, using 51 microcontroller to do, the use of C language
Upper-machine
- 嵌入式系统STM32与上位机通信程序，语言采用C语言-Embedded System STM32 and PC communications procedures, the language used C language