搜索资源列表
step.rar
- 步进电机按照细分控制所采用的程序代码设计，可实现精确步距控制,Stepper motor used in accordance with the fine control of the program code designed to achieve precise control of step
Step_motor
- DSP 2812 的步进电机控制程序 步进电机/延时不能太长，否则转得太慢 /延时也不能太短，否则频率太高不起转-DSP 2812 stepper motor control program stepper motor/delay can not be too long, or turn too slowly/delay can not be too short, or too high frequencies can not afford to turn
step_motor11
- 使用芯片为TI公司的DSP2812。该程序用以完成对交流电机的控制，启动/止、正转/反转、加速/减速。-Using TI s chips for the DSP2812. The program for the completion of the AC motor control, start/only, is to switch/reverse, speed up/slow down.
stepmotor
- 本程序是在CCS环境下利用C语言编写的一个控制步进电机的程序,其中包括控制电机的旋转速度、方向以及步数,从大体上概括了TMS320VC5402的片外围设备及I/O口的编程方式.-This procedure is in the CCS environment using C language under a stepper motor control program, including the control of motor rotation speed, direction, as wel
Step
- DSP实验箱EL-DSP-EXP-IV+若干实验程序之步进电机模块控制篇-DSP Experiment Box EL-DSP-EXP-IV+ a number of experimental procedures chapter stepper motor control module
step-control-on-DSP
- 采用F2812实现步进电动机控制的应用程序-Stepping motor control using F2812 application
stepping-motor(step-control)
- 电机的驱动程序，通过单片机来控制电机的转动，已通过测试，可根据实际情况直接调用-Motor driver chip to control the motor through the rotation, has been tested according to the direct call to the actual situation
step
- 控制步进电机的移动，基于51汇编，经过试验的，有详细的硬件电路图~-Control the stepper motor movement, based on 51 assembly, tested, and detailed hardware schematics ~
step-motor
- 步进电机程序 C8051F410驱动程序-Stepper motor driver application C8051F410
bujin
- 驱动4相五线步进电机的8分步,用于调速、正反转、基本的方法。-Drive 4-phase five-wire stepper motor step 8, for speed, rotating, and basic methods.
Step_Motor
- 步进电机，基于DSP2812，c程序,非常好用-step motor,based on DSP2812,c program，easy to use.
step
- 本程序是关于步进电机细分驱动的程序,里面有电机自适应细分的子部分-this procedure is about stepping motor which is dirved by subdividition.
step-motor
- 本实例详细描述了如何使用s7-200控制一台步进电机，包括详细的参数设置和实现过程。-This example describes in detail how to use the s7-200 to control a stepper motor, including detailed parameter settings and process.
step-motor-
- 步进电机参考程序 msp430 步进电机参考程序 msp430 -Motor reference programs for msp430
STEP
- DSP控制步进电机原理 由DSP输出的PWM3~6做为步进电机的4个信号线输入,选了PWM的IO口.-DSP controlled stepper motor principle by the DSP output for PWM3 ~~ four signal line input as a stepper motor, select the IO port of the PWM.
Step
- DSP TNS320F2812驱动步进电机程序-DSP drive a stepper motor program
step-motor.c
- 1，这是关于步进电机的细分电路。 2，这是关于步进电机原理说明。 3，这是关于步进电机MCS51+TLV5617(ADC)+A2916(MOTOR DIRVER)的源代码。-1，here is microstep motor driver circult and good code driver.
MOTOR-step
- DSP tms320f2812控制步进电机代码-DSP tms320f2812 stepper motor control codes
lab33-motor-step
- DSp28335 步进电机驱动程序 CCS4.x以上-dsp28335 motor-step
lab33-motor-step
- 基于TMS320F28335的电机控制程序，能够实现电机的启动和调试。(The motor control program based on TMS320F28335 can realize the start and debug of the motor.)