搜索资源列表
celiang
- 测量光敏电阻和热敏电阻的阻值，并显示在数码管和通过串口232传输到上位机-Measuring resistance and touch sensitive resistor, and is displayed in digital and serial transmission to the host computer 232
56pry
- 采集加速度计和磁强计的数据，并做姿态解算，然后将解算的三个姿态角传到串口上，采用的单片机是stc90c51rd6+-collect the data acccelerometer and meganetometer,then calculate the attitude,at last ,send the result to the com
GyroSensor
- 利用串口实时读取陀螺仪的数据，并根据读取到的数据进行基本的航向标定，结合数码盘可实现粗略的定位。-Use serial real-time read gyroscope data, and according to the data is read into the basic course of calibration, combined with digital plate of rough localization can be realized.
signal-generator
- 通过STM32控制AD9833芯片，实现利用按键切换正弦波、方波、三角波三种波形并控制频率10hz或20hz步进，全部有LCD显示。并可用蓝牙串口设置任意波形和频率-By STM32 AD9833 chip control, using the key switch sine wave, square wave, triangle wave frequencies, which are three kinds of waveform control 10 hz or 20 hz step, al
SmartUARTRT
- CC2540有并串口主从机的软件代码.可直接使用测试-CC2540 with and serial master slave software code.
2-zigbee_cc2530
- 终端节点每隔一段时间采集一次片内温度值，并将结果发送给协调器，同时亮一下led1；路由节点每隔一段时间采集一次电池电压值，并将结果发送给协调器，同时也亮一下led1；协调器每收到一个无线数据，就亮一下led2，同时将数据通过串口发送给电脑。是“LED”，则也亮一下led1。-............................................. no
ADC_DMA
- 一个多通道ADC转换DMA传输数据。程序是选择的通道0和通道1，各采集50次，然后滤波取其平均值，并发送到串口显示采样的电压值。-A multi-channel ADC conversion DMA transfer data. Program is selected channels 0 and 1, each collecting 50 times, then filtering the mean value, and sent to the serial display sampled v
temprature
- ARM9 S3C2440开发的不停循环检测温度值，并转换为ascii码，通过串口传出来的ADS工程-ARM9 S3C2440 development of non-stop loop detection temperature values and convert to ascii codes, coming out through the serial port of the ADS project
LCD1602JIA18B20
- 18b20测量温度。由液晶显示屏lcd1602显示温度。精确到小数点后两位,并由串口发送-18b20 measuring temperature. LCD1602 display temperature the liquid crystal display. Accurate to two decimal places，And sent by serial port
Robotics_3
- 智能小车的蓝牙控制功能实现，可以通过手机上的蓝牙串口助手连接小车并向小车发出指令。-Intelligent car Bluetooth control function, you can connect the car through the Bluetooth serial port on the phone and send instructions to the car.
18b20_6_chal
- 基于MSP430F5438a单片机 6路18B20采集温度 通过24L01传输 包含发送端接收端程序 接收端利用共阴极8位8段数码管循环显示6路数据 并通过串口传送到计算机- Microcontroller based MSP430F5438a 6-channel temperature acquisition by 24L01 18B20 transmission contains the sender receiving end program receiving terminal co
ZigBee--stack-driving-sht20
- ZigBee终端节点驱动sht20温湿度传感器采集数据，并将数据利用ZigBee协议栈发送到ZigBee协调器，协调器节点将接收到的数据通过串口显示到pc机。-ZigBee terminal node drive sht20 temperature and humidity sensors to collect data, and the data is sent to the use of ZigBee protocol stack ZigBee coordinator, the coordi
Alarm-sound-and-light-alarm
- 安防声光报警器：自制一个单片机最小系统，包括串口下载、复位电路，采用两路外部中断输入门禁和红外探测两路信号（采用两个小按键模拟），中断信号输入后能将报警信息在四位一体数码管上显示，并输出声光报警信号。-Security sound and light alarm: a homemade smallest single-chip system, including the serial download, reset circuit, using two external interrupt in
modbus-com
- modbus串口调试程序，发送命令给下位机，控制下位机并做出反应-modbus COMM program
robot
- pcduino从串口获取数据并解析后。控制pin引脚置高和置低。-pcduino get data the serial port and parsed. Control pin pin high and low.
MMA7455
- 利用CC2530实现IIC总线通信协议采集三轴传感器MMA7455数据，读取MMA7455的数据，并通过口串口在上位机显示 -Use CC2530 implement IIC bus communication protocol data acquisition triaxial sensor MMA7455, MMA7455 read data through the serial port on the PC display
DS18B20_USART
- stm32驱动DS18b20温度传感器，并将采集的温度打印到计算机的串口端-Stm32 drive DS18b20 temperature sensor, and will collect the temperature of the print to the computer serial port
stm32_usart1_rtc_timing
- stm32驱动RTC时钟，并将当前时钟数据通过串口发送内电脑-The stm32 drive the RTC clock, and within the current clock via a serial port to send data into the computer
SCPortRecData
- 串口读取磁感应数据的一个例子,用于下位机向上位机传输数据，上位机接收并显示到界面上-An example of the serial data read magnetic induction
Temperature-Sensor
- 用 stm32 测量温度 ，并通过串口显示-With stm32 measure temperature through the serial port and display