搜索资源列表
STC_2uart-sram
- 双串口收发多串口收发,单片机间的通信,实现很多的功能-Dual serial multi-transceiver serial port transceiver, single-chip communication to achieve a lot of features
LPC17xx-spi-master
- ARM LPC17xx 通过SPI同步串行接口发送数据给从机。-ARM LPC17xx send datas to the slave by SPI synchronous serial interface.
Rs485
- PIC18与串口RS485通信代码,已实验,可用-PIC18 and serial RS485 communication code has been experimental, available
an2557
- stm32实现了串口IAP功能,可以应对不同的硬件平台!-stm32 realized serial IAP function, you can cope with different hardware platform!
ARM_code
- 嵌入式系统关于串口传输、触摸屏、定时器、控制器、中断处理、音频控制等实验代码-Embedded system on the serial transmission, touch screen, timer, controller, interrupt handling, audio control experiment code
UART-CC2430
- 实现CC2430的无线通讯功能,实现无线的透时串口功能,即通过两个CC2430实现无线串口收发数据。-Achieve CC2430 wireless communications, wireless serial port when the permeability function that, by two CC2430 wireless serial send and receive data.
STM32-usart-programm
- STM32串口程序USART,自己调试成功的,可以运行,通过与电脑串口相连,可以观察传输的数据-STM32 serial program USART, the success of their own debugging, you can run through a computer serial port, data transfer can be observed
BCSP-and-ABCSP
- CSR BlueCore特有的但被广泛支持BCSP协议的上位源码,带项目文件可供编译测试和移值,含BCSP和ABCSP两种-BlueCore Serial Protocol (BCSP and ABCSP) user guides and source files
BCCMD_Protocol_(bcore-sp-002Pc).pdf
- CSR BCCMD protocol descr iption for serial communication with CSR BlueCore bluetooth chips.
Renesea_LED
- 瑞萨单片机的R8C系列的串口调试硬件和一个闪灯的软件全部工程,瑞萨单片机的资料太少,特别是串口调试的就更少了,更别说这种成套的资料,所以上这个成套的工程给用瑞萨单片机的同胞们,硬件中包括原理图,布好的PCB板,只要连接一个串口1再加上我给出的软件工程绝对就可以串口调试了。-Renesas R8C Family of serial chip debugging hardware and software, a flash of all the works, Renesas MCU little i
stm32-usart
- STM32F103的双向串口通信,KEIL环境,3.5的库-The STM32F103 bidirectional serial communication, KEIL environment
STM32Pdma
- STM32串口驱动(环形队列+内存动态分配+DMA+拼音检索)-STM32 serial driver (annular queue+ memory the dynamic allocation+DMA+ Pinyin retrieve)
uart
- st8s 串口程序,提供开发ST单片机参考!-st8s serial program, providing ST MCU development reference!
SoftwareSerial
- 已建成的Arduino硬件引脚0和1(也通过USB连接到电脑)的串行通信的支持.-The Arduino hardware has built-in support for serial communication on pins 0 and 1 (which also goes to the computer via the USB connection). The native serial support happens via a piece of hardware (built int
S2E-TI
- 嵌入式串口转以太网控制器,以下简称S2E21,是一款具有高效性能并集成了ARM Cortex-M3微处理器的串行至以太网控制器。该控制器的核心是高度集成的32位Stellaris LM3S6432 ARM Cortex-M3微处理器,具有50MHz性能和96K快速单周期片上闪存及32K SARAM内存,可高效处理网络流量。Stellaris系列微处理器采用LQFP-100 封装,并集成了片上10/100MB以太网MAC和PHY,从而能够最大限度的节省空间。-Embedded Serial to
HyperTerminal
- 基于8051单片机的超级终端仿真 超级终端,其实就一个输入输出设备,搞ARM的,这个东西可能再熟悉不过了,XP下就自带了一个,在 程序->附件->通讯工具->超级终端,可以看到。 我们通常是用基于串口的超级终端,即通过串口实现输入输出,来与CPU交互,控制CPU的执行。 -Super-based terminal emulation 8051 HyperTerminal, in fact, on an input output devices, engage
ADC
- MSP430F149的ADC模块,序列通道多次转换,转换好的值用1602显示,实测可用,绝不坑爹。-MSP430F149 ADC modules, serial channel number conversion, the converted value with the 1602 show, the measured available, not pit father.
uart
- 430通信程序,通过配置430URAT模块实现波特率9600 2400 15200串口通信-430 Communication Program, through the configuration 430URAT Module 9600 2400 15200 baud rate serial communication
ADkey8051F
- 本文介绍了如何用AD识别用户输入的键盘的方法,较之点阵识别有其不可替代的优势;因为如果用4*4的话须消耗8个I/O口,而如果系统有AD功能的话就可能轻松解决了。 单片机8051F330发给ARM然后发给电脑。 其原理就是利用电阻的分压,按键时产生不同的电压,再用中断快速读取电压;然后对其进行编码,通过串口软件EASYARM在个人电脑里显示;经实验观察,效果还可以。 -This article describes how to use AD to identify the user s
rs232
- AT89C58单片机 串口通信 利用rs232芯片-AT89C58 single-chip serial communication using RS232 chipset