搜索资源列表
UART.rar
- 主芯片：Actel的FPGA030,Verilog语言,串口发送和接收的例程，开发环境：LiberoIDE 8.5,The main chip: Actel' s FPGA030, Verilog language, the serial port to send and receive routines, development environment: LiberoIDE 8.5
uart
- 51单片机 串口接收发送 都用到中断 全双工 采用C语言-51 MCU serial port receive interrupt is used to send both full-duplex using C language
sc16is752
- sc16is752 device s firmware source code SC16IS752 is Dual UART with I2C/SPI interface, 64 bytes of transmit and receive FIFOs, IrDA SIR built-in support
UART-CC2430
- 实现CC2430的无线通讯功能，实现无线的透时串口功能，即通过两个CC2430实现无线串口收发数据。-Achieve CC2430 wireless communications, wireless serial port when the permeability function that, by two CC2430 wireless serial send and receive data.
SoftwareSerial
- 已建成的Arduino硬件引脚0和1（也通过USB连接到电脑）的串行通信的支持.-The Arduino hardware has built-in support for serial communication on pins 0 and 1 (which also goes to the computer via the USB connection). The native serial support happens via a piece of hardware (built int
Robosapien_IR
- Robosapien_IR.zip contains source files, PCB + Schematic and IR codes specification. The design is based on 8051 core mcu (I use P89C668 in my build), only minor modification needed with other brands of mcu. The board receive command code from serial
uart
- fpga 串行口 接收和发送程序，采用verilong语言编写-fpga uart ，receive and send include writed by verilog language
EX12_1_UART
- 將uart規劃成接收中斷，所以當使用者每次按電腦鍵盤時 進行類比訊號轉換，並將轉換結果輸出至UART-Planning into the uart receive interrupt, so each time you press the computer keyboard when a user when analog signal and convert results to the UART
simple-send-and-receive
- easyarm1138的ＵＡＲＴ的简单收发-easyarm1138 a simple UART receive
uart
- 如果使用查询的方式发送和接收数据 则不需要使用串口的中断-If the way to send and receive data using the query you do not need to use the serial port interrupt
UART
- 新世纪电子例程，MSP430F149单片机的，UART的串口通信例程，可以实现将收到内容转发出去。-Electronic routine for the new century of MSP430F149 microcontroller, UART serial communication routines can be achieved will receive forwarded out.
PIC24H-UART
- 1、这是PIC24H的UART底层驱动配置源码。 2、经过了优化和整理，分别有发送一个字节，接收一个字节，发送多个字节，接收多个字节的函数。 3、代码各行都有注释，清楚，方便使用，调试过可用。-1, which is the the PIC24H the UART underlying drive configuration source. 2, after the optimization and finishing, respectively send a byte, recei
CC2530UART1Test
- cc2530的uart串口通信 接收数据实例 可以直接用于实际中 很实用-cc2530 uart serial communication receive data instances can be directly used in the actual practical
UART-test-self-send-a-receive
- 单片机部分试验程序（89c51）,UART试验自收自发, -SCM part of the test program (89c51), UART test collected spontaneously,
uart
- MSP430G2553单片机，uart模块，中断收发数据，可以实时方便程序调试，分享大家-MSP430G2553 microcontroller , uart module , interrupt send and receive data in real time to facilitate debugging , to share
uart
- 编程控制开发板的UART0,实现与PC机的数据通信，完成字符的发送接收，字符串的发送接收-Programming control development board UART0, data communication with the PC, complete transmit and receive character string transmission and reception
UART
- STM8 串口单线输出（只发送，不接收），希望对初学者有用-STM8 serial single output (not only send, receive), I hope useful for beginners
UART
- stm32 固件库 串口中断调试 可发可收-stm32 serial port interrupt debugging， can send and receive
UART
- 采用的主控芯片LPC1768系列CORTEX-M3内核处理器，时钟晶振XT=12MHZ，系统时钟96MHZ，外部时钟PLCK 本程序采用查询方式完成串口的接收和发送程序 -Using master chip LPC1768 series CORTEX-M3 core processor, clock oscillator XT = 12MHZ, the system clock 96MHZ, the program uses an external clock PLCK query co
UART
- //DM430-A型开发板串口接收发送程序，使用单片机的串口0，显示操作通过串口调试助手 //通过电脑与串口线连接开发板串口座，使用串口调试助手发送数据到开发板板 //开发板板会将收到的数据再发送到串口调试助手，接收采用中断模块，发送用查询 //板载的BSL模块可以通过跳线帽设置为USB转串口模式，笔记本电脑没有串口可以直接代替 //开发板的BSL区的RXD和TXD0连接，TXD和RXD0连接即可 //注意使用BSL模块作为USB转串口功能的时候，RTS和TCK跳线帽、DTR