搜索资源列表
usart
- embedded c program for universal synchronous and asynchronous receiver and transmitter
ourdev
- 433m/315m无线解码资料，基于PT2272芯片自作。编码芯片PT2262发出的编码信号由：地址码、数据码、同步码组成一个完整的码字，解码芯片PT2272接收到信号后，其地址码经过两次比较核对后，VT脚才输出高电平，与此同时相应的数据脚也输出高电平，如果发送端一直按住按键，编码芯片也会连续发射。当发射机没有按键按下时，PT2262不接通电源，其17脚为低电平，所以315MHz的高频发射电路不工作，当有按键按下时，PT2262得电工作，其第17脚输出经调制的串行数据信号，当17脚为高电平期间3
cc1110-12232
- cc1110写12232液晶显示，无线收发，通过串口把十位的字符写到发射机上，再发送到接收机，显示到液晶屏上。使用iar编写生成hex。-CC1110 write 12232 LCD, wireless transceiver, through the serial port to send the ten characters to the transmitter, then send to the receiver, displayed on the LCD screen. Use IAR
IR_trans_rec
- MCU with IR transmitter and receiver source code ...
main
- stm8s M24C64 iic eeprom 源码-This firmware provides a basic example of how to use the I2C firmware library and an associate I2C EEPROM driver to communicate with an I2C EEPROM device (here the example is interfacing with M24C64 EEPROM) I2C per
Work_Rfm73
- RM73 interfacing pic16f series controller for transmitter and receiver
NRF24_RX_TX_ACK
- Sample project using NRF24l01 wireless transmitter with STM8S103 microcontroler
RF905_51
- RF905_51，无线发射模块，对应单片机开发板-RF905_51, wireless transmitter module, the corresponding microcontroller development board
Demo
- 用S3C2410和红外发射、接收二极管实现计数功能 （1）完成红外二极管与S3C2410的连接 （2）通过软件编程实现，两个红外管被阻断一次计数只加1（中断方式） （3）计数值显示液晶屏幕上 -S3C2410 and with an infrared transmitter and receiver diodes counting function (1) complete with infrared diode connected to the S3C2410 (2) thro
NRF_TX_Basic_v0.1
- nrf24l01 asb transmitter using avr mcu
LoRaTx
- LORA transmitter souce code to upload arduino -LORA transmitter souce code to upload arduino
temp-alarm-system
- Temeperture alarm system. This project has developed with CCS PIC C complier. Receiver and transmitter can communicate with PWM modulation to 1 km until. You can adjust alarm trigger on lcd display.
radio_config_Si4468
- This header file generated by Silabs WDS3 for si4468 radio transmitter-This is header file generated by Silabs WDS3 for si4468 radio transmitter
I2C_of_MSP430F249
- This demo connects two MSP430 s via the I2C bus. The master reads 5 bytes the slave. This is the MASTER CODE. The data the slave transmitter begins at 0 and increments with each transfer. The USCI_B0 RX interrupt is used to know when new data h
SIN-P300-RS485说明
- 485通讯，压力传感器485通讯协议代码，可以实现压力变送器与STM32芯片的通讯(485 communication, pressure sensor 485 communication protocol code, can realize the communication between the pressure transmitter and the STM32 chip)