搜索资源列表
san 配电网前推回代法三相潮流程序
- 配电网前推回代法三相潮流程序，收敛迅速，可靠收敛-Distribution network on behalf of the three-phase forward and backward flow procedures, rapid convergence, reliable convergence
mfix-2010.tar 多相流cfd程序
- 多相流cfd程序，用fortran实现，有多流体和dem计算功能，当然还有其它更多功能-MFiX is a general-purpose computer code developed at the National Energy Technology Laboratory (NETL) for describing the hydrodynamics, heat transfer and chemical reactions in fluid-solids systems. It has b
zc33
- 使用matlab编写的 配电网前推回代潮流计算程序 使用IEEE 33节点配电系统作为算例，可实现弱环网情况下的潮流计算-Matlab prepared using forward and backward substitution distribution network power flow calculation program uses IEEE 33 node power distribution system as an example, can be realized in c
dse
- 可以进行辐射状8节点配电网的状态估计，但是由于权重的选取不合适，程序收敛，但估计质量不高，可以通过合理的选择权重，来达到很高的估计质量。-Radial 8 nodes distribution network state estimation, but inappropriate due to the weight of the selected program convergence, it is estimated that the quality is not high, can be a
qiantuihuidai
- C++编制，配电网单相前推回代潮流计算程序，IEEE 33配电网作为算例，自己做项目编的-C++,, with single-phase power flow calculation forward and backward substitution procedures, IEEE 33 distribution network as an example, do their own project compiled
powerflow
- C#实现，前推回代法进行配电网33节点潮流计算-developed with C#,this is a distribution network load flow calculation program using forward and backward substitution method
nlf
- 计算电力潮流，通过输入PQ节点和PV节点以及导纳矩阵，计算整个网络的潮流分布以及线损-Calculation of the power trend, by entering the PQ and PV nodes and the node admittance matrix to calculate the trend of the distribution of the entire network as well as the Line Loss
example
- 计算竖壁集热器，在自然对流情况下流场以及温度场分布的cfd用户程序-Calculate vertical wall collector, in the case of natural convection field and temperature distribution downstream of the cfd user program
chaoliu
- 【配网潮流计算程序】本程序采用前推回代法，适用于35kV以下辐射型开式网络潮流计算，且若支路有备用支路需换算为单支路再行计算，适用于回路无环路时（有详细程序说明）。-【Distribution network load flow calculation program】 This procedure uses forward and backward on behalf of the law applicable to the following radiation-type open-35kV
paper
- This paper proposes a fault location method employing wavelet fuzzy neural network to use post-fault transient and steady-state measurements. When single line to ground fault (SLG) occurs in the distribution lines of an industrial system, the trans
N8090827
- 基于AT89C52的功率因数调整器是用于电力行业配电变压器用户侧无功补偿装置中的控制仪表，用于自动调整功率因数，使功率因数达到电力行业规定要求。-AT89C52-based power factor regulator for the power industry, the user side of distribution transformers and reactive power compensation device in the control instruments used to
COS
- 电力系统功率因数分析,能计算分析客户配电变压器用电情况-Power system power factor analysis, energy calculation and analysis of customer power distribution transformer
1
- Wind1.m读取文件“wind turbine parameters.txt”中关于风机参数生成文件“wind speed and pressure distribution.txt”同时做出wind speed distribution 和wind pressure1图-The code Wind1.m will read the parameters in file wind turbine parameters.txt and generate the wind speed and pr
nr
- 牛顿拉普逊法就算配电网重构的潮流程序，结构清晰易懂。-Newton Raphson method Rapp trend even if the distribution network reconfiguration process, clear and understandable structure.
distributed-generation_distribution-system_Newton-
- 优秀论文配套源码。分布式电源的接入使得配电系统从放射状无源网络变为分布有中小型电源的有源网络。带来了使单向流动的电流方向具有了不确定性等等问题，使得配电系统的控制和管理变得更加复杂。但同时，分布式电源又具有提高电网可靠性，绿色节能，等等优点，所以为更好的利用分布式电源为人类造福，我们必须对其进行研究与分析。 本文采取通过利用仿真软件Matlab编写计算潮流程序模拟分布式电源接入配电网的模型进行潮流计算的方法对分布式电源的稳态影响进行探索与分析。 选取了34节点的配电网网络模型，通过对单个
Distribution-power-flow-program
- 这是一个配电网潮流程序，基于c语言，与大家分享-Distribution power flow program, based on the c language, to share with you
Distribution-power-flow-calculatio
- 配电潮流计算，并包括IEEE的数据, -Distribution power flow calculation, and includes data of the IEEE
Distribution-System-3ph-fault-model
- Power Distribution 3 phase fault demo using simulink
Three-ph-distribution-line-measurement
- Three phase distribution system line parameters measurements
Distribution-power-flow-calculation
- 潮流计算程序，通过IEEE30节点验证，程序可以正确运行。-Distribution power flow calculation. IEEE30 node validation