搜索资源列表
wsd3
- 温湿度控制器(485通讯),开关量输出.-temperature and humidity controller (485 communications), the switch output.
ltm8901
- 长英科技的ＬＴＭ８９０１温湿度传感器Ｃ语言读写程序-long British technology LTM8901 temperature and humidity sensor C language literacy procedures
sht10.rar
- 一个温湿度控制的全部源程序，主要是介绍传感器SHT10的接口源代码。单片机是8051系列,A temperature and humidity control of all source code, mainly the introduction SHT10 sensor interface source code. 8051 series are single-chip
最终ZIGBEE温湿度采集
- 本精准农业系统以AT89S52为控制核心，通过DHT11数字温湿度传感器、实时采集农场环境的温度、湿度。通过zigbee模块传输数据，并利用LCD液晶显示屏1602显示数据。达到实时监控温湿度的目的。,The precision farming system for the control of the core AT89S52 through DHT11 digital temperature and humidity sensors, real-time acquisition of the
sht11
- 在51单片机上使用sht11传感器测量温度湿度。。这是用汇编语言编写的测量温度湿度数据，并且计算出温度湿度值的程序-In MCS-51 using sht11 sensors measure temperature and humidity. . It is written in assembly language measure temperature and humidity data, and calculated values of temperature and humidity pr
frequen
- 主要是测量湿度的程序，信不信有你，不信也没办法-The main procedure is a measure of humidity, believe it or not there you do not believe there is no way
atmega_lcd_tempe
- The HIH-3610 Series humidity sensor is designed specifically for high volume OEM (Original Equipment Manufacturer) users. Direct input to a controller or other device is made possible by this sensor’s linear voltage output. With a typical curre
1
- 采集0-7路输入来自直流源经分压器产生的0～5 V直流电压（可功能扩展，8路可接不同的传感器，采集不同的信号,例如:温度、湿度、图象、声音等）ADC0809将各路模拟信号分别转换成8位二进制数字信号,再对各路数据进行显示。各路通道采集方式为以约5s为周期循环采集（即0路、1路……7路、0路…）约每5ms更新，重新采集一次。显示方式为循环显示和单路显示：开关打开时，循环显示0-7路采集的数据；开关闭合时，显示当前单路采集的数据。3个七段数码管显示结果:最左边的一个数码管DS0显示通道号，其它两个数
sheji
- 由于将传感器与电路部分结合在一起，因此，该传感器具有比其它类型的湿度传感器优越得多的性能。首先是传感器信号强度的增加增强了传感器的抗-As a result of some combination of the sensor and circuit, so that the sensors have over other types of humidity sensors far superior performance. The first is the increase in sensor
mysht10
- SHT10-LED温湿度显示KeilC程序-SHT10-LED display temperature and humidity KeilC program
Wireless-Humidity-Transmitter
- 使用汇编语言编写的无线湿度变送器程序，已经经过仿真测试，可以用于具体实践或者设计-Written in assembly language programs for wireless and humidity transmitter has been tested by simulation can be used to design specific practice or
DHT21_11
- 温湿度传感器汇编程序，已通过编译，成功烧录-Temperature and humidity sensor assembly program, has been compiled by the successful burn
dht11
- C51 source code for temperature humidity sensor DHT11.
NEW2-305
- NEW2-305/306液晶显示调光/调速开关,采用PIC16C925单片机设计的可无级调光调速的控制程序，带LCD时钟显示，停电继续走时，有数字温度和湿度传感器，可实时显示环境温度和湿度，两个产品共用一个程序，通过硬件IO口识别，自动切换到调速或调光程序。-NEW2-305/306 the LCD dimming/speed control switch, the PIC16C925 microcontroller design stepless dimming governor contro
DH11-51
- DHT11温湿控制器源程序文件，正在学习，不知道怎样去编写数码管输出显示-DHT11temperatureand humidity control source
AM2302
- am2302控制程序,调整温度控制和湿度控制，得到相应的信号。-am2302 control program, adjust the temperature control and humidity control, to obtain the corresponding signal.
liangshicangkushiduwendu
- 粮食仓库温度湿度的检测文档 很好的哦 -Food storage temperature and humidity testing documentation oh well
1602
- 1602液晶显示温度 湿度 时钟.rar 1602液晶显示温度 湿度 时钟.rar 1602液晶显示温度 湿度 时钟.rar -1602 LCD temperature and humidity clock. Rar1602 LCD temperature and humidity clock. Rar1602 LCD temperature and humidity clock. Rar1602 LCD temperature and humidity clock. Rar1602 LCD t
changgui
- 实现常规预报的算法，包括24,48，和72小时内最高最低温度，降水等级，湿度，主要风向的判断。-Achieve conventional forecasting algorithms, including 24, 48, and 72 hours maximum and minimum temperature, precipitation levels, humidity, prevailing wind judgment.
HUMIDITY
- 基于汇编语言程序设计的湿度传感器的代码 用于实验板-Code in assembly language programming based humidity sensor For breadboard