搜索资源列表
RCRL
- RC/RL/LC电路的时间常数计算公式,主要用于电路设计时的RCL参数计算
RL-RTX-ARM-RTX
- RL_RTX实时操作系统详细描述，讲解（包含RTX_config讲述）-RL_RTX detailed descr iption of real-time operating system, explain
RLSchaoshengbo
- 针对超声换能器的传输特性随着温度和压力发生变化这一普遍存在的问题, 利用自适 应滤波技术对超声换能器的传输特性进行校正, 以减小温度和压力的变化对检测信号的影响。实测数据的处理结果表明: 基于RL S 算法的自适应滤波技术能准确地求出在不同温度压力条件下换能器传输特性变化的逆函数, 从而能很好地校正由于超声换能器传输特性随温度压力变化所引入的信号误差。-Ultrasonic transducer for the transmission properties change with tem
ZSI_without_filter
- IMPEDANCE SOURCE INVERTER FEEDING RL LOAD WITH CONSIDERABLE THD AND WITHOUT FILTER
ZLG7289-and-NUC120
- ZLG7289在芯唐UNC120上的应用，已通过RL-ARM Version 4.20编译并在硬件上成功运行。-Application of ZLG7289 core Tang UNC120 have been of RL-ARM Version 4.20 compiler and the hardware to run successfully.
DUI0374A_rl_usb_user_guide
- RealView® Real-Time Library Revision: r3p1 RL-USB User Guide-RealView® Real-Time Library Revision: r3p1 RL-USB User Guide
123
- 首先在直流通路中调节Rw使得ICQ=1.5mA。再连接好电路，用示波器观察输出波形（RL=5k）再将负载断开用示波器观察输出波形。高频实验资料。-First adjust the Rw in dc circuits makes the ICQ = 1.5 mA. Again good connection electric circuit, output waveform oscilloscope observation are used (RL = 5 k) then will load di
LTE--RLC-layer-AM-transmission
- 针对 3 G PP最新发布的 LTE ( l o n g t er m evol u t i on ) R e l ease 8 标准, 研究了 LTE 空中接口协 议栈无线 链路控 制 ( ra d i o l i nk con t ro, l RLC ) 的子层确认 ( ac kn o w l e d ged m o d e , A M ) 传输模式的 设计与实 现机制。主要介 绍了 L TE 无 线接入网空中接口协议 栈的结构, 详细阐述了空中接口协 议栈中 RLC的 A M 数据
RL_ARM_User__s_Guide
- RL arm descr iption document
ACTIVE-POWER-FILTER-TYPE-SHUNT
- This work shows the results of applying a shunt active power filter to compensate the harmonic currents generated by a three-phase controlled rectifier full wave, with the load linear circuits (RL).
rl
- this good for student to learn reinforcement learning-this is good for student to learn reinforcement learning
RLC_Circut
- This program to solve and plot Volt and Current of RL,RC and RLC
BAOCIZILIAOFENXI
- 建模仿真方法和过渡时间计算是磁饱和式可控电抗器研究中值得关注的2个重要问题.根据磁饱和式可控电抗器的饱和特性,通过对小斜率磁化特性的分析,找到了电抗器额定容量、额定电压、自耦比和绕组电阻之间的定量关系,明确了基于MATLAB的磁饱和式可控电抗器仿真模型参数的设置方法.通过对小斜率磁化特性的分段线性化,把从空载到满载的过渡过程分为直流磁链随时间线性增加和控制电流根据线性RL电路充电规律变化这2个过程,得到了比较准确的过渡时间计算公式.实例仿真结果说明所提分析方法简捷有效.-Modeling and
rtds-shuangguan
- 建模仿真方法和过渡时间计算是磁饱和式可控电抗器研究中值得关注的2个重要问题.根据磁饱和式可控电抗器的饱和特性,通过对小斜率磁化特性的分析,找到了电抗器额定容量、额定电压、自耦比和绕组电阻之间的定量关系,明确了基于MATLAB的磁饱和式可控电抗器仿真模型参数的设置方法.通过对小斜率磁化特性的分段线性化,把从空载到满载的过渡过程分为直流磁链随时间线性增加和控制电流根据线性RL电路充电规律变化这2个过程,得到了比较准确的过渡时间计算公式.实例仿真结果说明所提分析方法简捷有效.-Modeling and
2014-010233-Compiled-Report_
- explains how RL works
Sam-Azish-Compiled
- explains how RL works
single-phase-full-with-rl
- single phase full controller with rl load
single-phase-semi-controlled-converter-with-rl.ra
- single phase semi controlled converter with rl load
fullconverterWithRL
- FULL CONVERTER WITH RL LOAD
threelevel_voltagesource_RL_load_V2a
- Three level voltage source inverter with RL load