搜索资源列表
motor.rar
- 用51单片机实现了直流电机调速，附有PROTEUS仿真电路和PROTEL电路。,51 single-chip microcomputer with a DC motor speed control with PROTEUS circuit simulation circuit and PROTEL.
step_driver_ln298
- 本驱动程序主要针对L298驱动的步进电机，用MSP430单片机编写，在自动控制设计中应用广泛，且有较好的驱动功率。-The main driver for the L298 stepper motor driven, with the MSP430 microcontroller is written in the automatic control design is widely used, and there is a better drive power.
L298
- 基于ARM7的L298驱动程序，芯片L298，控制两个直流电机，没有用PWM调速-Based on ARM7-L298 driver chip L298, control two DC motors, there is no speed control with PWM
ad
- 1.A/D转换 2.编码器数据采集 3.电机驱动 利用ADC0809芯片，编码器采用74LS193,idt7205进行增减计数，电机驱动采用8253和L298芯片.-1.A/D converter 2. Encoder Data Acquisition 3. Motor drive using ADC0809 chip encoder using 74LS193, idt7205 to increase or decrease in counting, motor driver ch
Motordriver
- 单片机通过L297和L298驱动两项步进电机，按键可以切换电机的速度和方向，并且在LCD上显示出来。有完整的Proteus图和C语言程序，运行结果良好。-Singlechip L297 and L298 through two stepper motor-driven, button to switch the motor speed and direction, and displayed in the LCD. Proteus has a complete map and C languag
l298
- this a helpful source code -this is a helpful source code
stepmotorcontrol
- L297和L298控制两相步进电机源码，带密码锁定功能-L297 and L298 stepper motor control of two-phase source with a password lock function
297-298
- L297 应用文档 讲述L297 和L298 配合 作步进电机的细分-L297 and L298 application documents about the L297 stepper motor with a breakdown of co-operation
car
- 用VHDL实现的红外循迹小车程序，采用8个红外二极管（装在车头底部）识别路况，接L298电机驱动电路，能跑白色背景下的黑色赛道，且能应付道路分叉，孤岛及自启动等。-Implemented using VHDL infrared tracking car program, using eight infrared diodes (mounted on the front of the bottom) to identify traffic, then L298 motor driver circu
forward-reverse
- 实现智能小车的前进和后退动作，小车电机由L298驱动，本程序控制L298的三个输入端即可-complete a small car s forward and reverse action,power is supplied by L298
1
- 这是一个使用51单片机加上L298驱动直流电机的程序源代码。-This is a single chip using 51 L298-driven DC motor with source code.
DianJi
- 基于ARM的直流电机驱动，能正反转，停止启动，采用了L298作为驱动-ARM-based DC motor drive, to reversing, using the L298 as a driver
L298
- 仅仅使用L298驱动芯片，主控为51单片机，在keil中调试测过，专门驱动步进电机的！不是直流电机。-Just use the L298 driver chip, the master microcontroller 51, in keil debugging measured before, specifically to drive stepper motor! Not a DC motor.
bujindianjiceshichengxu
- 一个简单的步进电机测试程序，用L297,和L298芯片带动步进电机-A simple stepper motor test program, with the L297, and L298-chip stepper motor drive
zhiliudianji
- 运用L298驱动直流电机，代码中包含有正转、反转、停止等程序。-DC motor driver using L298, the code contains a forward, reverse, stop and other procedures.
vbRobot_Source-code
- this a robot by At89C2051 and control in visual basic, The source code is asm code & frequnce test is in 315MHZ,drive 2 motor dc by l298.enjoy!
STM32-315McontrolLEDCAR
- 基于STM32单片机/315M无线模块控制智能小车 直流电机驱动 通过实现对LEDs 的控制，可以实现L298 （A或和B电机）的控制，达到对小车的控制（前进倒退转弯） 应用很简单，直接用L298需要的引脚接LED-Ports-Based on the STM32 MCU/315M wireless modules to control the smart car DC motor drive through the realization of the control of
moteur-pas-a-pas-unipolaire
- stepper motor command with th famous circuit l297 and l298 tested and validated in tunisia
L298
- L298电机的驱动芯片，有完整的电路图，有很大的帮助的，使用它-L298 motor driver chip, a complete circuit, there is a lot of help, use it
L297-l298-pic16f88-4hilos
- Acciona motor paso a paso con pic16f88, puente H l298-l297 mas simulacion Proteus, mueve motor isquiera y derecha +-velocidad y enable/disable