搜索资源列表
sys(matlab)
- 某控制系统的开环传递函数的分析.绘制系统的闭环根轨迹，寻找系统临界稳定时的增益k，并分析其稳定性。-a control system of open-loop transfer function analysis. Rendering System is a closed-track, Find Critical stable gain k, and to analyze its stability.
routhtablepaper
- 利用Matlab编写程序实现以下功能：以多项式形式输入系统前向通路传递函数和反馈回路传递函数，计算系统开环增益，判定型别，根据控制系统劳斯稳定判据原理，列出得到的任意阶次系统的劳斯表，判定闭环系统稳定性，若不稳定给出具有正实部极点的数目。 （1）根据用户输入的稳定度a，计算稳定的开环增益K的范围； （2）确定系统的最大稳定度a,计算相应的开环增益K的值。 -The use of Matlab programming to achieve the following functions
OP07_a
- The OP07 has very low input offset voltage (75 μV max for OP07E) which is obtained by trimming at the wafer stage. These low offset voltages generally eliminate any need for external nulling. The OP07 also features low input bias current (±4 nA
rls_identifikation
- RLS identification algorithm. RLS is used to identify a discrete time model of a plant operating in open-loop based on the recursive least squares method and the UD factorization for updating the adaption gain matrix (F).-RLS identification algori
MC34119[1]
- The MC34119 is a low power audio amplifier intergrated circuit intended (primarily) for telephone applications, such as in speakerphones. It provides differential speaker outputs to maximize output swing at low supply voltages (2.0 V minimum).
181336261208
- 可变增益放大器是模拟单元电路之一,起着变化增益、调整信号动态范围、稳定信号功率的作用。文章综述了CMOS集成可变增益放大器的研究情况 给出了可变增益放大器的定义、应用、分类和主要指标,描述了多种开环和闭环放大器的结构,分析了相应的增益控制方法及其优缺点 说明了在CMOS工艺下实现放大器增益按指数变化的几种途径。最后,介绍了用于无线数字通信,具有宽带、高线性、低电源电压等高性能可变增益放大器的设计实例。-Variable gain amplifier circuit of the analog u
pgpi
- PGPI(NUM,DEN,W,FI,A) plots the stability boundary locus L(KP,KI,W)in the (KP,KI)-plane for an LTI system with transfer function defined by its NUM, DEN coefficients and driven by a PI controller with transfer function, C(s)=kp+(ki/s). Frequency (W) g
ruanjiansheji
- 以中等纯度的精馏塔为研究对象，考虑到不等分子溢流的影响和非理想的汽液平衡，可以得到塔顶产品轻组分含量Y与回流量L之间的传递函数为： 控制要求： 1.采用积分分离 PID控制算法将塔顶轻组分含量Y控制在0.99 2.采用继电法整定PID参数 3.整定效果验证：当被控过程参数时变时，如滞后时间由4→8，开环增益由3.4→6时, 讨论PID控制的响应速度及鲁棒性问题，考察当系统参数发生改变时，上述PID参数是否选取合适。 -Moderate purity fr
spica-ruanjian-ziliao
- 采用积分分离 PID控制算法将塔顶轻组分含量Y控制在0.99 2.采用继电法整定PID参数 3.整定效果验证：当被控过程参数时变时，如滞后时间由4→8，开环增益由3.4→6时, 讨论PID控制的响应速度及鲁棒性问题，考察当系统参数发生改变时，上述PID参数是否选取合适。 -Using integral separation PID control algorithm to control the top of the tower light component content Y
Runge_Kutta
- 龙格库塔法进行控制系统的数字仿真.输入开环增益k,输出超调量和调节时间，并打印阶跃响应曲线。-Runge-Kutta method of digital simulation of the control system to enter the open-loop gain k output overshoot and adjustment time, and print step response curve.
4.8k_CELP
- 语音CELP压缩解压源代码（C语音)- Pronunciation CELP compression decompression source code (C pronunciation) - * 4800 bps CELP Characteristics * * Spectrum Pitch Code Book * ------------- ---------------
Qinghua-University-PLL-Lecture
- PLL的设计与频率相应 清华大学的讲义 基于低通滤波器的设计绘制开环增益波特图-PLL DESIGN AND FREQUENCY GENERATION Draw open-loop gain Bode plot based on LPF design
genguijitu
- 根据已知的开环传递函数绘制出系统的根轨迹图，再进而找到使闭环系统能够稳定的增益的取值范围-According to the known open-loop transfer function draw root locus of the system, and then turn to find the closed-loop system to stabilize the gain of the range
openloop
- open loop luo convertor Voltage Lift Technique has been successfully employed in design of DC/DC converters, e.g. four series Luo-Converters. However the output voltage increases in arithmetic progression. Luo series Elementary, Re-lift an
Control Loop Design and Step Response
- Derive and express the open loop gain T in the analytical closed form according to