搜索资源列表
uart
- uart application used for android platform. Extract the package and excute compile commond and push app to anddroid paltform, then you can test it.
A11上位机C51代码
- HF-A11 UART to Wifi 透传模块C51控制源码
UART.使用FPGA的FIFO，状态机
- 使用FPGA的FIFO，状态机，乒乓操作等实现了异步UART。,The use of FPGA-FIFO, state machine, ping-pong operation to achieve the asynchronous UART.
uCos-uart-driver.rar
- uCOS-II内核分析,在单片机上实现uCOS-II的移植,同时在该操作系统上实现uart驱动,uCOS-II core analysis, in SCM to achieve uCOS-II of the transplant, at the same time in the operating system to achieve UART driver
uart.rar
- 实现串并口通信,共有发送和接受两个模块。,Strings parallel to achieve communication, send and receive a total of two modules.
UART.rar
- 主芯片：Actel的FPGA030,Verilog语言,串口发送和接收的例程，开发环境：LiberoIDE 8.5,The main chip: Actel' s FPGA030, Verilog language, the serial port to send and receive routines, development environment: LiberoIDE 8.5
LM3SAPP_Bootloader_UART_Note.r
- Luminary单片机,LM3S系列单片机串行（UART）升级应用笔记。介绍 LM3S系列单片机如何通过串行（UART）接口 更新用户程序。 通过使用Luminary Flash Programmer软件可以有以下功能： 1. 通过 LM LINK 可以对 Flash 进行编程、擦除和对调试端口（PB7、PC0~PC3）解锁； 2. 可以通过 UART 对 Flash进行编程； 3. 可以通过以太网对 Flash进行编程。 ,Luminary monolithic integ
uart
- 51单片机 串口接收发送 都用到中断 全双工 采用C语言-51 MCU serial port receive interrupt is used to send both full-duplex using C language
CC1110-Uart
- CC1110单片机串口的使用方法，通过串口可以将无线数据上传至电脑观察-Usage of CC1110 UART , it will trans data to PC
uart_rt
- stm8的uart的收发例程，利用中断，将接收的字符，重新发出去-stm8 the uart to send and receive routines, the use of interrupts, will receive the characters, re-issued to
CC2430-uart
- 介绍了ZigBee CC2430的串口收发字符串的源程序，用IAR软件可以直接打开使用-Introduced the ZigBee CC2430 transceiver serial port of the source string, using IAR software can be used directly to open
uart
- stm8的uart例程，不带库的，对uart进行初始化，向串口发送数据-stm8 the uart routines, without the library, on the uart to initialize, send data to the serial port
uart
- 采用软件方法来实现单片机的通用串口引脚来模拟UART。根据要求采用P1.0作为发送端（TXD）,P1.1做为数据接受端（RXD），并采用全双工通信模式。由于MAX232电平转换芯片除了做UART的几个引脚后，还剩余T2IN,T2OUT,R2IN,R2OUT.所以采用模仿UART的接法.每次通信，发送的数据加1，接收的数据加2.用51系列单片机。-The use of software methods to achieve single-chip Universal Serial pin to s
UART
- 包含一个在QUARYUS环境下运行的UART的工程，实际在EP2C20Q240上调试成功的通用串口VHDL程序-The QUARYUS environment contains a UART to run the project, the actual success of the EP2C20Q240 Universal Serial debugging VHDL programs
uart
- 用veriolg 语言编写的串口通讯程序，通过FPGA控制串口的通讯。-a veriog program completed on FPGA to contrlo a uart to communicaton with a computer
iic-spi-uart
- 基于FPGA的IIC,SPI,UART接口协议的实现。-FPGA-based IIC, SPI, UART interface protocol implementation.
uart
- atmega8、16 uart的标准模板，写程序时直接包含即可，很方便的-uart to atmega8、16
UART-to-I2C
- I2C UART to I2C-PIC12FF1840-UART to I2C-PIC12FF1840 UART to I2C-PIC12FF1840
uart-TO-SPI-FLASH-20130226
- 代码实现了电脑向uart 发送四个字节（命令1字节 地址3字节）然后 对M25Pxx系列的芯片进行任意地址的读写， 目前只实现单字节默认数据的读写！有需要的可以 修改-uart to spi control the M25PXX IC
UART-to-Bus-Core-Specifications
- The UART to Bus IP Core is a simple command parser that can be used to access an internal bus via a UART interface. This core can be used during initial board debugging or as a permanent solution when high speed interfaces are not required. The i