资源列表
STM32-serial-port-driver
- STM32串口驱动(环形队列+内存动态分配+DMA+拼音检索)-STM32 serial port driver (circular queue+ memory dynamically allocated+ DMA+ phonetic retrieval)
ADS8341-module-test-program
- ADS8341与mega16单片机连接，ADS8341模块测试程序。-ADS8341 connected with the mega16 microcontroller the ADS8341 module test procedures.
Ultrasonic-application
- 超声波应用程序，可以精确地测试1m之内的距离。采用mega16单片机，有12864液晶显示。-Ultrasonic application, you can test accurate test 1m of distance. Mega16 microcontroller, 12864 LCD.
PID-DC-motor-control
- mega16单片机控制的直流电机调速系统。-mega16 microcontroller to control the DC motor speed control system.
ExtLinesTrigger
- 用两个外部中断触发ADC规则转换和注入转换。 ADC1配置为在EXT11事件发生时启动规则通道组的ADC转换。当检测到PE11引脚 的上升沿时，启动第1个规则通道（ADC通道4)转换，转换结果通过DMA传输到ADC_RegularConvertedValueTab 数组。在PE11的下降沿，第二个规则通道（ADC通道14）自动开始转换，转换结果通过DMA传输到同一个数组。-Two external interrupt to trigger the ADC rules o
elc_weight
- icc环境下的电子秤程序，包括A/D转换，flash数据存储、can通信、串口通信等功能很全。-icc environment electronic scales under the program, including the A/D conversion, the function of flash data storage, can communications, serial communication is very full.
51MCU_music-player
- 基于keil的51单片机音乐播放器，并在proteus上做仿真，语言为c语言-Keil 51 microcontroller music player, and in proteus simulation language c language
Stepping-motor-and-PWM
- 基于单片机设计步进电机系统。5轴步进电机联动-模拟数控系统c源程序；PWM直流电机恒速运行c程序-The stepper motor system based on single chip design. 5-axis stepper motor linkage- CNC simulation system c source PWM DC motor constant speed c program
WsnPcMonitorForJiang
- 单片采集温度信息通过串口发送到PC机的上位机显示软件，可以远程控制灯光气体温度等信息，并时时显示各种参数变化曲线-The monolithic collect temperature information sent through the serial port to a PC host computer software can remotely control lighting gas temperature and other information, and always show t
TFT3.5--ILI9481
- 点3.5寸屏的程式，用的是ARM7的平台，弈力9481的IC，供参考。-Point program of 3.5-inch screen, with the ARM7 platform chess power IC 9481, for reference.
disp
- 用数码管前两位显示一个十进制数，变化范围为00~59，开始时显示00，每按下S2键一次，数值加1；每按下S3键一次，数值减1；每按下S4键一次，数值归零；按下S5键一次，利用定时器功能使数值开始自动每秒加1，再次按下S5键，数值停止加1，保持显示原数。-Digital tube first two shows a decimal number, range 00 to 59, the beginning of display 00, press S2 button once, increment
ad
- 用单片机控制ADC0804进行数模转换，当拧动实验板上A/D旁边的电位时，在数码管的前三位以十进制方式显示出A/D转换后的数字量（8位A/D转换后数值在0~255变化）。-SCM ADC0804 digital to analog conversion, when the twist on the experimental board next to the A/D potential, the top three digital tube shown in decimal, digital A