资源列表
hello
- fpga单片机入门第一步通过按键点亮第一个小灯-The fpga single-chip machine enters the first step by pressing the key to light the first light
ledbuff
- fpga单片机通过数码管实现1S自加功能，时间通过计数器实现-The fpga single chip machine implements the 1S self-addition function through the digital tube, and the time is achieved through the counter
2410
- s3c2410开发板源程序 包括LED灯、按键、串口等 很齐全-S3C2410 development board source
51_DHT11
- 温湿度传感器DHT11的驱动程序 微处理器平台为宏晶公司的STC15W4K56S4。已经测试成功。-Temperature and humidity sensor DHT11 driver, microprocessor platform for Acer crystal company s STC15W4K56S4. Have been tested successfully.
DS1302
- 基于ATmega16A单片机的DS1302实时时钟芯片驱动程序。已测试成功。-DS1302 real-time clock chip driver based on ATmega16A microcontroller. Successfully tested.
NIS-07-Smoke-sensor
- NIS-07烟雾传感器的资料 为烟雾探测类产品的设计提供数据参考-NIS-07 smoke sensor datasheet
InitPeripheral
- LPC1778外设初始化，包括GPIO、Systick、Timer0、CAN、UART、ADC，工程刚调试好，完全没有任何问题，初始化调用的是库函数-LPC1778 peripherals initialization, including GPIO, Systick, Timer0, CAN, UART, ADC, engineering just debugging good, there is no problem, the initial call is the library func
STC15W4K56S4PENC28J60PuIP-Stack
- 在STC15W4K56S4 单片机上移植了uIP Stack协议栈 完整的5层TCP/IP 协议栈。以太网物理层使用的是ENC28J60集成芯片。-The uIP Stack protocol stack is transplanted on the STC15W4K56S4 microcontroller, and the Ethernet physical layer uses the ENC28J60 integrated chip.
RingFIFO
- 循环缓冲区，做的所有项目都是调用这个RingBuf，可靠程度较高，缓冲区元素长度可自由设置为char、long、struct等-Loop buffer, do all the projects are called the RingBuf, a higher degree of reliability, the buffer element length can be freely set to char, long, struct, etc.
oscilloscope
- 简易虚拟示波器制作协议后面在发上来。主控用的是STM32的芯片。-Simple virtual oscilloscope production agreement behind the hair
Electronic-circuit
- 3. 创建一个工程文件，编程实现将0 1 2 E F、姓名等显示在LCD屏上，编程实现将3到4位数据小数点后保留一位（如10.2、100.6）分别显示在三组LED屏上。 4. 编程实现按键输入功能，将按键信号显示在LED或LCD屏上，（如按▲键，,使屏幕信号逐渐加1，从0加到10，再按▼键，从10减到0。 5. 编程实现D/A转换（下行通道），输出（4~20mA）电流，并进行0点和斜率校正。 6. 编程实现A/D转换（上行通道）实现数据采集，将采集信号显示在LED和LCD屏上。程序要
24bujindianji
- 步进电机 5线4相 51单片机- U6B65 u8FDB u7535 u673A 5 u7EBF4 u76F8 51 u5355 u7247 u673A