资源列表
NIS-07-Smoke-sensor
- NIS-07烟雾传感器的资料 为烟雾探测类产品的设计提供数据参考-NIS-07 smoke sensor datasheet
InitPeripheral
- LPC1778外设初始化,包括GPIO、Systick、Timer0、CAN、UART、ADC,工程刚调试好,完全没有任何问题,初始化调用的是库函数-LPC1778 peripherals initialization, including GPIO, Systick, Timer0, CAN, UART, ADC, engineering just debugging good, there is no problem, the initial call is the library func
STC15W4K56S4PENC28J60PuIP-Stack
- 在STC15W4K56S4 单片机上移植了uIP Stack协议栈 完整的5层TCP/IP 协议栈。以太网物理层使用的是ENC28J60集成芯片。-The uIP Stack protocol stack is transplanted on the STC15W4K56S4 microcontroller, and the Ethernet physical layer uses the ENC28J60 integrated chip.
RingFIFO
- 循环缓冲区,做的所有项目都是调用这个RingBuf,可靠程度较高,缓冲区元素长度可自由设置为char、long、struct等-Loop buffer, do all the projects are called the RingBuf, a higher degree of reliability, the buffer element length can be freely set to char, long, struct, etc.
oscilloscope
- 简易虚拟示波器制作协议后面在发上来。主控用的是STM32的芯片。-Simple virtual oscilloscope production agreement behind the hair
Electronic-circuit
- 3. 创建一个工程文件,编程实现将0 1 2 E F、姓名等显示在LCD屏上,编程实现将3到4位数据小数点后保留一位(如10.2、100.6)分别显示在三组LED屏上。 4. 编程实现按键输入功能,将按键信号显示在LED或LCD屏上,(如按▲键,,使屏幕信号逐渐加1,从0加到10,再按▼键,从10减到0。 5. 编程实现D/A转换(下行通道),输出(4~20mA)电流,并进行0点和斜率校正。 6. 编程实现A/D转换(上行通道)实现数据采集,将采集信号显示在LED和LCD屏上。程序要
24bujindianji
- 步进电机 5线4相 51单片机- U6B65 u8FDB u7535 u673A 5 u7EBF4 u76F8 51 u5355 u7247 u673A
juzhenanjiankongzhishumaguan
- 矩阵按键数码管移位显示 已通过编译,下载运行正常- U77E9 u9635 u6329 u952 u651 u7L1 u7B1 u7Fl
NUC100_120BSP_v3.00.001_SPIToI2S
- 新唐nuc100系列,利用spi模拟i2s总线的代码-i2s port emulated by spi port in nuvoton nuc100 series.
34343436sfdd
- 51单片机教室智能照明控制系统 原理图+PCB 仿真图 源程序-51 MCU, intelligent lighting control system principle diagram of+PCB simulation source code
STM32-oscilloscope
- STM32示波器,2.4寸TFT屏,支持频率计算、时基调整、峰值测量、程控增益控制等功能-STM32 u793A u6682 u5668 uFF0C2.4 u5BF8TFT u5C4F uFF0C u652F u6301 u9891 u7387 u8BA1 u7B97 u3001 u65F6 u57FA u8C03 u6574 u3001 u5CF0 u503C u6D4B u91CF U3001 u7A0B u63A7 u589E u76
jsoncpp
- 海思Hi3536的JSONCPP开发环境,包括库文件和头文件-Hi3536 JSONCPP开发环境