资源列表
CHECK
- 本迷宫小汽车选用8位STC90C52单片机为控制器，通过3个红外光电传感器E18-D80nk对信号进行采集，采集到的信号经串口转换MAX232CPE处理后传给STC90C52单片机，经单片机处理后，发出控制命令给L298N，驱动2台直流电动机进行相应的动作。该小车实现了前进、后退、左右转弯、避障以及显示运行时间等基本功能，整个系统结构简单，可靠性高，实验测试结果满足要求-STC90C52 microcontroller pass the maze of car use 8 STC90C52 si
come-on
- 数字电压表的编程,基于51单片机进行的编程，采用AD0809进行模数转换，具有报警以及设置上限电压功能。-Programming digital voltage meter, 51 microcontroller based programming, using the AD0809 analog to digital conversion, has the functions of alarm and set the upper limit voltage.
jianpansaomiao
- 通过C8051F单片机实现键盘扫描和键值散转，并控制SD卡文件显示在LED屏上。-C8051F MCU keyboard scanning and the key bulk transfer and control SD card file is displayed on the LED screen.
new-42
- stm8s903无刷电机无感控制器开发程序，适合初学者学习-the stm8s903 brushless motor no sense of the controller development program for beginners to learn
servos-control-
- 利用单片机定时器 脉宽调制控制舵机 可以参考一下-The use of single-chip timer pulse width modulation control servos can refer to
USR-TCP232
- 网络协议调试助手，用于网络模块和PC机的通信测试-Network protocol debugging assistant for network module and PC communications test
stm_32_nrf24l01_
- nrf2401无线模块，stm32程序实现了数据双向通信，被遥控端一次发送四个数据同时接收一个数据，遥控端一次接收四个数据，同时发送一个数据。完全匹配，可以串口助手调试程序。-nRF2401 wireless module STM32 program to achieve a two-way data communication, the remote end to send four data while receiving a data remote end receives four da
ir-rc5
- 基于单片机89C51的红外解码采用延时加查询红外端口的方法-89C51 microcontroller-based IR decoding delay plus the infrared port on
ST7920proteus12864
- 带中文字库的12864在proteus中的仿真-12864 with the Chinese character simulation in proteus
C-xunji-NEW
- 5路 小车 循迹C51代码 TCRT5000 探头-5-way car tracking the C51 code TCRT5000 probe
simulation_51_pressure_sensor
- 基于proteus的51单片机压力传感器的仿真，仿真结果分别用lcd和led显示-Proteus 51 microcontroller pressure sensor-based simulation, the simulation results were used to LCD and LED display
ex886
- LED显示技术 1.制作数字时钟，用LCD正常显示时分秒 2.通过按键可改变显示方式，内容为时钟信号 3.设计显示屏的动态技术，用10个按键，每键对应一种滚动技术。-LED display technology to create digital clock with LCD display properly, minutes and seconds. Buttons can change the display mode, the clock signal design dynam