资源列表
keil c6.20c 直接嵌入汇编的方法
- keil c6.20c 直接嵌入汇编的方法-Keil c6.20c embed compilation methods
DYJ
- 电压监控,通过监空电压,来判断出口,从而控制继电器. -Voltage monitoring, voltage and air through the supervisor to determine the export and thus control the relay.
valctr
- PT2258 is a 6-Channel Electronic Volume Controller IC utilizing CMOS Technology specially designed for the new generation of AV Multi-Channel Audio System. PT2258 provides an I2C Control Interface, an attenuation range of 0 to -79dB at 1dB/step,
sg1
- AVR片内EEPROM读写访问示例软件编程
hongludeng
- 1、程序目的：使用定时器学习 倒计时 红绿灯原理 主要程序和倒计时一样 2、硬件要求：数码管、晶振12M-1, the program aims: to learn to use countdown timer process and countdown traffic lights as the main principle 2, the hardware requirements: digital control, crystal 12M
LED-jiaotongdeng
- 说明：东西向绿灯亮若干秒，黄 灯闪烁 5 次后红灯亮， 红灯亮后，南 北向由红灯变为绿灯，若干秒后南北 向黄灯闪烁 5 此后变红灯，东西向变 绿灯，如此重复。-Descr iption: something to a few seconds the green light, yellow light flashes 5 times the red light, red light after red light into green light from the nort
shoufa
- 这是一个关于RS232串行通讯的程序，它实现了把接收到的数据立即再发回去的功能-This is an RS232 serial communications program, which implements the back function of the received data immediately recurrence
PTZ_89C51_D
- 云台镜头控制板的源程序，采用89C51单片机，C语言源代码，实际测试通过。 环境STC51单片机配11.0592晶振，支持协议pelco-d，采用485和RS232均通过测试，2400BPS。地址码按默认1.**是51芯片上的程序可不是电脑PC上的控制程序。测试用电脑上和用监控键盘均可以控制。编译通过Keil_C.-PTZ control panel source 89C51 microcontroller C language source code, through the actual t
add-leds-speed
- C8051f120的AD程序，调节电位器控制八个led灯的亮灭和闪烁频率-C8051f120 the AD process, adjust potentiometer control eight led lights out and flicker frequency
LPM3
- msp430F149,说明：此程序运行在LPM3 MSP430通常在4秒的时间间隔，脉冲P3.4。 WDT ISR用来唤醒系统。- Descr iption: This program operates MSP430 normally in LPM3, pulsing P3.4 at 4 second intervals. WDT ISR used to wake-up system.
ds18b20
- 采集DS18B20的温度 并显示于数码管上-DS18B20 temperature acquisition and display on the digital
hld
- 程序是东西红灯亮30秒，南北绿灯亮24秒 东西红灯亮，南北绿灯闪3秒然后熄灭 黄灯亮3秒-Program is what turns red, 30 seconds, north and south green light 24 seconds Red light, the north and south green light flash for 3 seconds and then go out Yellow lights for 3 seconds