资源列表
2410
- ucosII在arm920T内核s3c2410移植的代码.-ucosII in arm920T s3c2410 transplant kernel code.
classicalarithmeticofPID
- 本程序提供了经典PID算法的优化算法，适合单片微控制器的应用，请大家共享并提出宝贵的意见!-the procedures of classical PID algorithm optimization algorithm suitable for single-chip microcontroller applications, Please share and for the valuable advice!
MSP430
- iar编译器调试msp430单片机c程序详细教程-iar compiler debugging MCU Controller c procedures detailed guidance
duojikongzhi
- 舵机控制程序，舵机的控制信号为周期是20ms的PWM信号，其中高电平持续时间0.5到2.5ms。-steering control procedure, the servo control signal is 20ms cycle of the PWM signal. margin which lasted 0.5 to 2.5ms.
moto_PWM
- 直流电机驱动芯片采用Ｌ２９８．支流电机驱动就是利用ＰＷＭ脉宽控制Ｌ２９８电流输出大小，从而达到控制电机的目的-Motor Driver IC using L298. Tributaries is the use of motor-driven PWM pulse width control L298 current output size, so as to achieve the purpose of the electrical control
EDA
- 程序在报告中，要 用QuartusII运行，注意从word到运行环境中，可能有个别符号不兼容，重新在运行环境中输入那些符号就可以了-procedures in the report, with QuartusII operations, the attention to word from the operating environment, Some individual symbols are not compatible, the operating environment to re-e
HT1380
- ＨＴ１３８０时钟芯片控制程序，ＨＴ１３８０采用串行传送数据，可记录年，月，日，星期，小时，分和秒．-HT1380 clock chip control procedures, HT1380 using serial transmission of data, can record the year, month, , weeks, hours, minutes and seconds.
Eda1
- 程序在报告中，要 用QuartusII运行，注意从word到运行环境中，可能有个别符号不兼容，重新在运行环境中输入那些符号就可以了-procedures in the report, with QuartusII operations, the attention to word from the operating environment, Some individual symbols are not compatible, the operating environment to re-e
UART0tiaoshilicheng
- Ｃ８０５１Ｆ０４０的ＵＡＲＴ０调试程序，ＵＡＲＴ０模式１主机程序，ＴＸ０线为Ｐ０.０，ＲＸ０线为Ｐ０.１，ＴＸ０采用Ｔ２为波特率产生源，ＲＸ０采用Ｔ１为波特率产生源-C8051F040 UART0 debugging procedures, a model UART0 mainframe procedures, TX0 lines of P0.0 and P0.1 RX0 lines, T2 TX0 used for baud rate generator, RX0 using T1 for b
ORG0000H
- 单片机应用＿＿交通灯程序报告，用汇编语言编写，注意程序在word中的逗号可能要改一下，才能在wave6000中用-SCM application procedures for traffic lights, using a compilation of language, attention to the procedures of the word may have to change a comma that can be used in wave6000
ADC0danduanshurumoshi
- Ｃ８０５１Ｆ０４０的ＡＤＣ０单端输入模式，定时启动，由Ｔ２定时，选择ＡＩＮ０.３为ＡＤＣ０转换通道-C8051F040 ADC0 the single-end input mode, the regular start, the T2 timing, ADC0 AIN0.3 choice for channel conversion
ADC0zhuanhuan
- 基于C8051F040的利用过采样实现16位ADC转换的程序-based on the use C8051F040 over 16 sampling ADC conversion process