资源列表
stm32-modbus
- 在STM32系统下实现MODBUS功能，实现简单易懂(Realize MODBUS function in STM32 system, easy to understand)
基于AUTOSAR的ECU软件开发方法
- 基于autosar的ECU软件开发方法，适合初学autosar的工程师，比较容易入门(Development Method of ECU Software Based on Autosar)
交通灯控制
- 包含proteus仿真文件及c语言程序，在开发板上进行过运行。利用双色LED显示电路，和四位静态数码管显示电路模拟十字路口交通信号灯。4位LED数码管显示时间，双色LED灯显示红绿灯状态。熟悉交通信号灯控制逻辑。设计一个十字路口的交通灯控制电路，要求南北方向和东西方向两个交叉路口的车辆交替运行。每次绿灯变红灯时,要求黄灯先亮3S,才能变换运行车辆。东西方向、南北方向车道除了有红、黄、绿灯指示外，每一种灯亮的时间都用数码管显示器进行显示（采用倒计时的方法）。考虑到特殊车辆情况，设置紧急转换开头。(
GenY工具生成驱动程序
- 该文档有助于你使用VECTOR公司的GENy软件，用于生成协议栈(This document helps you to use VECTOR's GENy software to generate protocol stacks)
AD5934驱动程序（stm32）
- AD5934 stm32f103驱动程序； 测量PT100温度探头计算温度； 测量电极间阻抗并换算成电导率。(AD5934 stm32f103 driver; Measuring the temperature of the PT100 temperature probe; The impedance between the electrodes is measured and converted into conductivity.)
sht3x
- sht3x驱动程序，基于stm32f0平台(Sht3x driver, based on stm32f0 platform)
无人机避障
- 模拟了无人机遇到障碍物自动避障的原理，并且加了大量的注释！(The principle of UAV avoiding obstacles automatically is simulated, and a lot of comments are added!)
STM32 BootLoader升级固件+HAL_Flash读写
- 本内容主要描述STM32BootLoader升级以及内部flash操作的常规步骤，本资料仅为相关代码的编辑，仅供参考(This content mainly describes the normal steps of stm32bootloader upgrade and internal flash operation. This material is only for the editing of relevant codes and is only for reference)
STM32全套集成库
- 包含了STM8、STM32F1/2/3/4、STM32L1、STMW系列单片机原理图及封装图，可用于PCB软件画图。(Including STM8, stm32f1/2/3/4, STM32L1, STMW series MCU schematic diagram and package diagram, can be used for PCB software drawing.)
F1最小系统
- STM32F103C8T6最小系统原理图和PCB工程(Stm32f103c8t6 minimum system schematic and PCB Engineering.)
AN1078
- 电机驱动入门资料，完全中文解释，有点小bug但无伤大雅，基本没问题，熟悉之后运行电机无感无刷电机完全没问题(The introduction data of motor drive is completely explained in Chinese. It's a little buggy, but it's harmless. Basically, it's OK. After getting familiar with it, it's OK to run the motor sensel
8405050b
- 智能电表实现电流、电压、频率、功率检测功能(Intelligent ammeter realizes the function of detecting current, voltage, frequency and power)