搜索资源列表
stepper_PWM
- Stepper motor control on Atmel AT91SAM7A3 with PWM and SPI.
PID1
- dc motor control using pso
85375520dsPIC30F
- 非常好的dsPIC数字信号控制器C语言程序，其中包括AD转换、数字滤波、电机控制程序等等。-A very good dsPIC digital signal controllers C language program, including the AD conversion, digital filtering, motor control procedures.
aa
- proteus仿真4线步进电机控制，适合初学者学习-proteus simulation 4 wire stepper motor control, suitable for beginners to learn
ucOS
- 介绍将实时嵌入式操作系统μC/ OS - II 移植到TMS320L F2407A 芯片的过程,构建了以DSP 为硬件基 础、以实时操作系统μC/ OS - II 为软件平台的深海机器人推进电机的控制系统。采用嵌入式操作系统的 数控系统,具有优异的实时性和更高的智能化水平,同时也降低了数控系统的开发难度。-Introduction to real-time embedded operating system, μC/OS- II ported to TMS320L F2407A chip
1_speed_control_pid
- DC MOTOR CONTROL PID USING MATLAB and SIMULINK
Three_phase_tiaosu
- 此程序内包含三相异步电机的调速各种仿真，希望对大家有用。-This program contains a variety of three-phase induction motor speed control simulation, want to be useful to everyone.
ourdev_259644
- 基于矢量控制的永磁同步交流伺服电机控制系统程序-Based on Vector Control for Permanent Magnet Synchronous AC servo motor control system programs
svpwm
- 基于空间矢量电压算法的SVPWM控制模型，对于电机控制建模有很好的帮助作用。-Algorithm based on space vector SVPWM voltage control model, for motor control modeling are very helpful.
bujingdianjikongzhi
- 步进电机正反转及调速控制，本代码为步进电机的控制程序代码，包括汇编代码和C代码-Positive inversion and speed control of stepper motor, the code for stepper motor control program code, including assembly code and C code
motor
- 基于matlab/simulink环境，对异步电机的一个仿真，能够得到完整的仿真结果，是直接转矩控制的基础部分。-Based on matlab/simulink environment, a simulation of the induction motor, can be a complete simulation results, is a fundamental part of the direct torque control.
Rotor_Field_Orientated_Control
- This paper presents rotor field orientated control (RFOC) and direct torque control (DTC) of the five-phase induction motor, and their fully digital implementation based on the TI s TMS320C32 DSP. RFOC and DTC, two important motor control methods,
SPWM_1.0
- 该软件实现了SPWM，能够对永磁同步电机实现变速控制，软件各模块独立，程序移植性高-The software implementation of the SPWM, can achieve variable speed permanent magnet synchronous motor control software modules independent, porting high
DSP
- 基于DSP DSP320F2812感应电机控制系统-Based on DSP DSP320F2812 induction motor control system
A_real-time_adaptive_PID_controller_step_motor
- 传统PID控制器通常难以满足多变量、非线性、强耦合的步进电机动态响应和精 确调速要求,结合传统PID控制和模糊控制及遗传算法(GA)整定PID参数的优点,设计基于 模糊遗传算法的实时自适应步进电动机PID控制器,充分发挥传统和智能控制策略各自的优 势。仿真结果表明,该实时自适应步进电动机PID控制器,具有很好的自适应能力和抗负载扰 动能力。在稳定性、动态速度响应诸方面均优于传统的PID控制器和模糊控制器,系统达到了 较高调速性能和控制精度。 -Traditional PI
Five-phase_hybrid_stepping_motor_control_technolog
- 本文研究了混合式步进电动机原理结构和运行特性，由于混合式步进电动机 结构特殊，状态方程高度非线性且各状态变量相互祸合，使得数学公式难以准确 的表达。据此提出了考虑饱和非线性的五相混合式步进电动机的数学模型，并用 MATLAB对相电流进行了仿真研究，本文在分析五相混合式步进电机的数学模 型的基础上，推导出了电机运行矩频特性的计算公式，并在考虑磁路饱和的情况 下，对绕组电感参数做了非线性分析和处理。在MATLAB的环境下对其进行了 仿真，仿真结果基本符合实际情况。 -Fi
motor
- 设计制作和调试一个由MCS51单片机组成步进电机角度系统,它能利用单片机控制步进电机的角度控制和角度显示方法。-Design and debugging a form from the MCS51 microcontroller stepper motor point of the system, it can use the angle of stepping motor control and point of display methods.
DCCL
- DC motor control for closed loop using cc studio for 2407 DSP-DC motor control for closed loop using cc studio for 2407 DSP..
sheji
- 三相交流异步电机直接转矩控制的MATLAB仿真-Three-phase AC induction motor direct torque control of MATLAB Simulation
DSP2812-Motor
- 利用DSP的PWM1和PWM2,然后经过了两级放大控制直流电机，若要改变电机转速或转向,可在DSP28_EV.c文件里按相应注释修改，即实现PWM波来控制电机。-Using DSP-PWM1 and PWM2, and then amplified through a two DC motor control, to change the motor speed, or steering, can DSP28_EV.c file comments by corresponding changes