搜索资源列表
CIS_CPLD
- 用s3c44b0x和 CIS（ContactImage Sensor) 传感器接口-with s3c44b0x and CIS (ContactImage Sensor) sensors Interface
cis_100dpi_dsp
- 程序实现了采用CIS+AD9822+FPGA的结构形式对人民币进行采集。然后把采集到得数据通过EMIF接口传送给DSP。已通过调试-Program implements the use of CIS+ AD9822+ FPGA structure in the form of the RMB is collected. Then the data collected was transmitted through the EMIF interface to the DSP. Has passed
3Channel_CIS_Processor_with-VHDL.ZIP
- This usefull source for control CIS Sensor and has fallowed functions 1) Read image data frome 3channel 200dpi CIS Sensor 2)Encoder Sync Technoledge for more high resolution analiysys with shared the time divition 3)Psudo Video Ram Read by
vidiocpt
- 本代码为富士通MV86S02的CMOS图像传感器的VHDL驱动代码-The code for Fujitsu MV86S02 the CMOS image sensor-driven VHDL code
sv253A4
- 这是接触式图像传感器（cis）的手册，个人觉得这个手册对这类新型的图像采集器件介绍得比较详细，透彻，值得学习。-This is a Contact Image Sensor (cis) of the manual, personally feel that the manual for such a new type of image capture device descr iption was more detailed, thorough, worth learning.
pd6710
- 基于PCMCIA接口代码，主要实现读取存储卡寄存器配置，确定PC Card所需要的资源并对他进行配置。软件设计主要包括两方面，一是PCcard侧的ARM控制器对CIS的初始化程序；另一方面是PC侧的驱动程序。-Based PCMCIA interface code, main memory card reader configuration register to determine the PC Card and the resources required to configure him.
fpgacis
- 主要是通过使用FPGA利用CIS（接触式图像传感器）进行图像采集，通过AD转换之后把数据存储到FPGA里面开辟的FIFO-Mainly through the use of FPGA utilization of CIS (non-contact image sensor) image acquisition, through the data storage after AD transform to open the FIFO FPGA inside
cli_parser-0.4.tar
- 一个开源的CLI解析引擎，Cisco Like的风格；很不错。 核心代码小巧，容易移植到到单片机等嵌入式系统，实现命令行控制等等。-An open source CLI parsing engine, Cisco Like style very good. Core code is compact, easy to transplant to the MCU and other embedded systems, control, etc. to achieve the command l
lowpowerfir
- This project was undertaken to produce a low power FIR filter for inclusion in a VHDL target library. The design was completed using OrCAD s Capture CIS, from this the VHDL code has been extracted. This method has allowed complete testing of the syst
CIS
- source code for arm 2440
CIS
- S3C2440开发板Wince下CIS实现的例子！-S3C2440 development board under the CIS implementation example Wince!
CIS
- MINI 2440开发板配套WINCE 系统下C#程序--CIS程序
Stepper-motor-driver
- 采用热转印制作 PCB ，电路采用2相推挽全桥驱动，单片机采用 STC54C12C5404 具体的模式如下：五种模式选择 一:停止。 二:顺时针转2分钟，停6分钟，循环； 三:逆时针转2分钟，停6分钟，循环； 四:顺指针转2分钟停6分钟，逆时针转2分钟停6分钟，循环； 五:顺指针转5分钟，逆时针转5分钟持续3小时，停9小時，循环。 -Thermal transfer production of PCB circuit using 2 push-pull phase full-b
anjianshebei
- 通过3x3键盘的1~8号键控制8个LED的ON/OFF切换，9号键控制步进电机的顺时针/逆时针切换，INT按键控制蜂鸣器的ON/OFF切换。通过串口打印信息，包括：8个LED的ON/OFF情况、步进电机的顺/逆时针和蜂鸣器的ON/OFF状态 ；每一次按键均应触发一次打印； -By 3x3 keypad numbers 1-8 keys to control 8 LED s ON/OFF switch, the 9th keys to control the stepper motor CW/