搜索资源列表
arm-bits
- 最好的置位操作函数，是ARM公司源码的一部分-the best home-manipulation functions, ARM is part of the FOSS
fet140_spi
- MSP-FET430P140 Demo - USART0, SPI Interface to HC165/164 Shift Registers Descr iption: Demonstrate USART0 in two-way SPI mode. Data are read from an HC165, and same data written back to the HC164. ACLK = n/a MCLK = SMCLK = default DCO = UCLK
lpc01_ds1820.zip
- LPC ARM7 32 Bits DS1820 functions,LPC ARM7 32 Bits DS1820 functions
CalcCRC
- CalcCRC8 The CalcCRC8 is used to append an eight-bit CRC to the message. A successful CRC check results in returning a 0. Implementation: This CRC will be using the CRC-16/CITT protocol. A 16-bit wide non-reflected code that starts initially
EasyARM1138UART
- 本例是easyarm1138的UART(通用异步收发器)实例 建议采用Windows自带的“超级终端”来调试UART， 在“端口设置”里，设置如下 波特率：9600 数据位：8 奇偶校验：无 停止位：1 数据流控制：无 -This case is easyarm1138 the UART (Universal Asynchronous Receiver Transmitter) proposed to u
lpc01_crc8
- LPC ARM7 32 Bits crc8 algorithm functions
lpc01_delay
- LPC ARM7 32 Bits delay functions
UART_RVMDK
- 本源码为STM32的UART使用例程,主要测试UART1的功能。开发环境realviewMDK 程序运行前先打开串口调试软件，UART被配置为： 波特率：9600bps 字长 ：8位 校验位：无 停止位：1位 程序正常运行，调试软件的数据接收区将显示ASCII码字符表中的‘0’到‘z’范围内的字符；同时开发板上的小灯LD3～LD6将会顺序点亮，然后顺序熄灭。-The source code for the STM32' s UART to use routines,
main
- 程序是凌阳单片机编写的，用三个键位控制步进，方法简单，很适应于小系统，程序用c语言实现对DAC输出电流的控制 -Sunplus program is written by three key bits control the stepping method is simple, it is adapted to small systems, the program using c language implementation of the DAC output current control
sd_card
- SD card using FAT file system This example application demonstrates reading a file system from an SD card. It makes use of FatFs, a FAT file system driver. It provides a simple command console via a serial port for issuing commands to view and naviga
aduc7060code
- 带24位AD的ARM芯片ADUC7060全部硬件资源测试代码,MDK下的-Take 24 bits of AD ADUC7060 all hardware resources ARM chips, the test code MDK
shiyan7
- 简易频率计，测量范围为8位，0到10000000。-Simple frequency meter, measuring the range of 8 bits, 0 to 10000000.
ALU
- Its an ALU of 32 bits.
card-reader-module
- 北京圆志科信读写卡模块,M104X_V1_2,UART接口一帧的数据格式为 1个起始位，8个数据位，1个地址/数据标志位，1个停止位。波特率：19200，方式3，11位格式。-Beijing Yuan Zhi Kexin card reader module, M104X_V1_2, UART interface, a data format is 1 start bit, 8 data bits, 1 address/data bits, 1 stop bit. Baud Rate: 1920
WEN
- 通过定时中断实现14位的温度湿度采集的完整kielc51程序。-By timer interrupt temperature and humidity of 14 bits full kielc51 collection procedures.
RTC-set-the-clock-and-display
- RTC时钟源为外部低速时钟，且外部低速时钟源的64分之一Tamper引脚（PC.13)上输出。 通过秒中断功能，在LED1(GPIO_Pin_0)上以2s为周期闪烁，并以1s为周期通过USART送出时间信息 （在串口调试软件上以24小时时间制显示） USART1设置：波特率：9600 数据位：8 停止位：1 奇偶校验位：无 硬件流控制：无 注：编译时，Library Configuration应选为FULL，以使C库函数fputc映射到U
dulishijianpan
- 独立式按键的显示程序，四位8段LED显示-This register is used for specific configurations on memory remap. Two bits are used to configure the type of memory accessible at address 0x0000 0000. These bits are used to select the physical remap by software and so, byp
led_liushui.mcp_0_backup
- LED的流水灯程序设计，LED数码管显示-This register is used for specific configurations on memory remap. Two bits are used to configure the type of memory accessible at address 0x0000 0000. These bits are used to select the physical remap by software and so, byp
paomadeng
- 跑马灯程序，可以连续的循环，不间断LED法官二极管显示-This register is used for specific configurations on memory remap. Two bits are used to configure the type of memory accessible at address 0x0000 0000. These bits are used to select the physical remap by software and
key_led
- 行列式键盘，四段8位LED显示，包括键盘扫描，分段显示-This register is used for specific configurations on memory remap. Two bits are used to configure the type of memory accessible at address 0x0000 0000. These bits are used to select the physical remap by software and