搜索资源列表
reg89c5131
- This a header file for 8051 Keil uVision 3 This using Keil uVision 3 and Atmel Flip 3.4.3 The code is tested using 8051 microprocessor chip. 1) Copy and paste the attached code to Keil uVision. 2) Use the link below to configure in Keil fo
SD2403
- 国产RTC SD2403驱动程序，已经调试，各应用函数很全，但改单片机需你自己下点功夫-Domestic RTC SD2403 driver has to debug the application of a function is very full, but change the MCU need your own point effort
1.Led_Blink
- 使用stm32的sram调试程序，包括ini文件的编写和程序地址的修改（将下载程序的地址从flash映射到sram）-debug stm32 chip in the sram,include ini file and change the address of program (from flash to sram)
zhongxinxiantiqu
- 智能车图像采集程序，包括中断处理，图像二值化，串口调试，中心线提取等，做智能车的可以参考参考。-Intelligent car image acquisition program, including interrupt handling, binary image, a serial port debug, from such center line, do intelligent car can reference reference.
12864
- 12864多级菜单_调试通过源程序，基于51系列单片机，系统功能十分强大，可实现显示时间，日期以及记分器，设定密码等操作。-12864 multi-level menu _ debug through the source, based on the 51 series microcontroller, the system function is very powerful and can display time, date, and scoring device, set password
DC-motor-cesu
- 设计制作和调试一个由MCS51单片机组成的直流测控系统。掌握直流电机的速度控制和测试方法。 要求完成的主要任务: （1）定义键盘按键：5个为数字键1～5；3个功能键：设置SET、清零 CLR、开始START； （2）显示器上的四位可显示每分钟的速度； （3）通过键盘的按键，设置直流电机每分钟的速度值； （4）按START键启动电机开始转动，按SET键停止；按CLR键清零。 以上包括proteus仿真图，源程序-DC measurement and control sys
uart
- 51单片机串口通讯的程序，利用串口调试助手和pc机通讯，很好的资料哦-51 SCM serial interface communication program, using a serial port debug assistant and PC communications, very good material oh
chuankoutiaoshi
- 图像处理，打开一张图像，进行串口调试，利用单片机进行控制-Image processing, open an image, for a serial port debug, using single chip computer control
c51teachcode
- 图像处理，打开一张图像，进行串口调试，利用单片机进行控制-Image processing, open an image, for a serial port debug, using single chip computer control
serial-communication
- 用于51系列单片机与计算机之间的串口通信，信息的发送可通过串口调试软件实现-Used for serial communication between the 51-series single-chip computer, the message is sent through the serial port debug software
host-computer
- 通过单片机之后的数据传输到上位机，用Csharp编写的代码，已经调试运行过了-Through the MCU after the data is transmitted to the host computer, prepared by the Csharp code, have been debug run over
12864Serial-port-debug
- 超声清洗系统-操作控制部分程序，按键操作处理，存储调整后的数据。-Ultrasonic cleaning system
stm32canrxandtx
- stm32的can总线调试方法详细介绍。-the stm32 The bus can debug method described in detail.
Touch-screen
- 大家可以用MODBUS协议通过人机界面来调试程序或学习通信协议。 1.使用前，需要安装GUIBuild触摸屏组态软件，软件在"\单片机开发工具\GUIBuild触摸屏组态软件" 2.使用GUIBuild和OPS6触摸软件前，先双击学习光盘中的“KeiLib.exe” 3.软件安装好后，双击Test.op6 即可运行程序。 4.使用GUIBuild触摸屏软件时，先编译，再选择在线模拟，再选择正确的COM口后点击连接。-Through man-machine
chuankou--debug-txt
- PROTEUS 虚拟串口调试教程,串口调试初步入门参考资料。-PROTEUS virtual serial port debugging tutorial, serial debugging initial entry references.
STC12c5608
- STC单片机读写ADS1110,iic读写，调试成功-STC microcontroller to read and write ADS1110，iic read and write, debug successful
6264_storage
- atmega32接6264存储器的调试程序，写入值后读出显示，显示采用的是串行移位方式-this is the debug program of 6264 storage,in this program,first write data in the storage,the read them from the storage,and display in end.
uart1
- 实现ADC0采样芯片温度，通过LCD显示，并通过串口1（J13）发送到PC机,请使用串口调试工具调试！-ADC0 sampling chip temperature, LCD display, and through the serial port (J13) is sent to a PC, use serial debugging tools to debug!
Smart_Car_Debug
- 飞思卡尔智能车 摄像头组调试小软件 对于平时调车分实用很方便-Freescale smart car debug it,s a goog tool to make smart car,and it,s very conveinent~
Two
- 使用DAC0808实现不同精度的多级数字调压用例，并搭建其外围电路并通过调试验证-DAC0808 accuracy of multi-level digital voltage regulator for use cases, and to build its peripheral circuit and through the debug and verify