搜索资源列表
spp_dev_a
- BLUETOOTH UART/USB 通信(SPP,Cable Replacement)Master端源代码.-BLUETOOTH UART / USB Communication (SPP. Cable Replacement) Master-source code.
spp_dev_b
- BLUETOOTH UART/USB (SPP CABLE REPLACEMENT)SLAVE端源代码.(开发环境,BLUELAB362)-BLUETOOTH UART / USB (SPP Cable REPLACEMEN T) SLAVE-source code. (development environment, BLUELAB362)
ReticleTEST.rar
- 自制单片机东东\网线测试 测试网线的通断。 ,Self-made single-chip Dongdong \ test test cable network off-line.
serial_comm
- DTR/DSR handshaking is used because this is what the POS printer requires. Comms with a pc can then be accomplished using the same cable as used for the printer. Ensure that the pc program is written to use the same handshaking.
qianrulanya
- 以TI的TMS302VC54x数字信号处理器（DSP）为嵌入式控制器、ERICSSON的蓝牙模块为例，在蓝牙电缆替代协议应用模块的基础上，提出一种将电缆替代协议进行扩展的嵌入式蓝牙应用模式及其硬、软件的实现-The TMS302VC54x to TI digital signal processor (DSP) for embedded controllers, ERICSSON Bluetooth module, for example, in the Bluetooth cable repl
bafo_1284_write_to_port
- this zip code sends data to the parallel port using bafo 1284 parallel port cable
RS232Cable
- it is OBD-II to RS232 cable for ISO 9141-2
temprature
- 本文介绍了以"一线总线"的数字方式传输的DS18B20温度传感器为测温核心，用单片机AT89S51构造控制电路，利用数码管及其它外围元件组成显示单元，通过ISP方式进行程序的编制、用并口连接线下载单片机程序和以MAX232 芯片设计RS232串口电路并通过串口连接线进行调试，设计、制作了一种电子测温计。-This article describes the " bus line" of the digitally transmitted DS18B20 core tempera
shuziwenduji
- 数字温度传感器DS18b20试验,用连接线将JH端子的DS12B80位与CN7或CN8的P37口相连运行此程序,温度值将在数码管上显示.用手触摸T1芯片(DS18B20)观察温度变化.-Digital temperature sensor DS18b20 test, with connecting cable terminals DS12B80 JH bit and CN7 CN8 of the P37 port or connected to run this program, the tem
xilinxJTAGSCHPCB
- xilinx JTAG 下载线 SCH 和 PCB，本人在网上下载到的-xilinx JTAG download cable SCH and PCB, to which I downloaded from the Internet
CEREBOT32MX4-LED-Demo
- Required Hardware • Digilent Cerebot 32MX4 • USB A to Micro-B Cable • Digilent Pmod8LD (optional)-Required Hardware • Digilent Cerebot 32MX4 • USB A to Micro-B Cable • Digilent Pmod8LD (optional)
VisualizationToolExample
- Code Warrior 5.1环境下应用VisualizationTool可视化调试的一个例子。-This project is an HC12 ANSI-C project. This example is running the "Demo" program on: -the CodeWarrior HC12 Simulator, (choose "Demo (Simulation)" target), -ICD12 P&E cables interface (ICD12
es_isp_diy_by_machao
- avr isp 下载线 原理图 绝对很好用 只要焊接正确 一定可以成功-avr isp download cable schematic absolute good use right will be a success as long as the welding
Download-cable-production
- 详细介绍了ISP下载线制作的过程，里面有电路图和各种电器的型号参数，该下载线能为很多拥有笔记本的朋友们解除usb转rs232的烦恼。而且成本很低-ISP download cable described in detail the process of production, there are a variety of electrical circuit diagrams and model parameters, the download cable for a lot of friend
Nike_iPod_Serial_Schematic.pdf
- Schematic on interfacing with Nike Plus ipod transmitter directly with a serial cable
CableTester
- 并行电缆检测的PLC程序，基于三菱FX2N，用LED阵列显示设置和比较结果。Y0为公共地-Parallel cable testing PLC program, based on Mitsubishi FX2N, with the LED array display settings and compare results. Y0 for the public GND
Measured-twisted-pair-instrument
- STC89C52单片机构成主控部分，进行主要的信息处理，接收测线模块的数据，进行处理，形成各种控制信号；测线模块经过单片机的控制对被测网线的通断性进行检测，并将数据传输给单片机处理；单片机控制LCD使检测结果显示出来，并指出被测线路的问题。- STC89C52 MCU main control part is composed, performed primarily on the information processing, the receiving line module data, p
PCBaYUANLI
- 电缆通断检测PCB及原理图，西北工业大学电子信息学院。-Cable on-off detecting PCB and schematic, Electronic Information College of Northwestern Polytechnical University.
Computer-communicate-by-Zigbee-
- 两个zigbee模块通过串口接在两台电脑上面，两台电脑上面运行串口助手，可以实现通过串口助手发送至zigbee模块，再通过无线模块传送至另一个zigbee模块上，这个zigbee将数据发送至相应的电脑上，通过UART实现点对点无线通信，使用方法如下： 1：打开IAR开发环境，打开工程。 2：接上仿真器，并把仿真电缆连到CC2430模块上，把程序下载到两个模块上。 3：两个模块之间通过PC机串口发送一个字符到另一个模块的PC。-Two zigbee module through th
AVR-arduino-minisys
- 该编程器使用ISP并口下载线，所以电路相当简单。在这份资料中还 给出了一个ATmega8最小系统板的电路图和PCB，只要把ISP下载线接到该 系统板上即可下载程序到单片机里。-The programmer uses ISP parallel port download cable, so the circuit is quite simple. In this item are also given an ATmega8 minimum system board schem