搜索资源列表
HoughObject
- Circles We can extend the Hough transform to other shapes that can be expressed parametrically. For example, a circle of fixed radius can be described fully by the location of its center (x, y). Think of each feature (edge) point on the circle
roundCenter
- vc2008 dos 程序 已知AB两点坐标，半径R。 求2个圆心。 公式使用MATLAb推导的，做了一点简化，和小的改动。 都在函数 double jisuanYanxin(double Ax,double Ay,double Bx,double By,double R) 里面-vc2008 dos program known AB two coordinates, radius R. Seeking two center of the circle. Formula de
BallFretting190809
- This tool is a simplification of the ballpivoting algorithm. It imagines a bella eating a delaunay traignulation in order to extract a manifold surface. It requires a single parameter: radius of the fretting ball. Ball Fretting Given a unif
cylinder2
- [X,Y,Z]=cylinder2(x,y,z,r,N,o) 向量X，Y，Z轴定义圆柱面中心线 和矢量r定义圆柱面半径，并已 为的x，y，z的长度相同 N是周围围点的数量。默认值 为N= 100。 Ø 定义了矩阵圆柱generatix（圆圈）椭圆 表面。其内容以0和1之间的值，并适用于 小学和中学的母线轴。值的defeault Ø =的（长（x），2）。 矩阵X，Y，Z轴确定圆柱面，冲浪
rengongmianyi
- a=load( q.txt ) width=input( 请输入窗宽 ) step=input( 请输入步长 ) m=length(a) for i=1:floor((m-width)/step+1) s(i,1:width)=a(1,1+(i-1)*step:width+(i-1)*step) end b=max(max(s)) M=s./b Rs=input( 请输入本体集半径 ) nd=input( 请输入检测器数模 ) k=1 while
cylinder2
- [的X，Y和Z] = cylinder2（的x，Y，Z轴，俄，氮，氧） 向量X，Y，Z轴定义圆柱面中心线 和矢量r定义圆柱面半径，并已 为的x，y，z的长度相同 N是周围围点的数量。默认值 为N= 100。 矩阵Ø 定义了准线（圈）椭圆圆柱 表面。其内容以0和1之间的值，并适用于 小学和中学的准线轴。值的defeault Ø =的（长（x），2）。 矩阵X，Y，Z轴确定圆柱面，冲浪（的X，
susan
- mallest Univalue Segment Assimilating Nucleus is used to extract the edge and corner points of local feature area. The principle of operator SUSAN is to make a mask on the circle area of one point with the radius of r and then observe every point in
test
- 这个程序可以画出一个给定圆心和半径的圆，参数分别是x，y，r。-This program can draw a circle and the radius of a given circle, parameters are respectively the x, y, r
RBNN
- Algorithm based in graph theory, in which form cluster around of a radius r of a point.
example_8_end
- 自行车轮饰物的运动轨迹。路面视为光滑曲线f(x),饰物离车轮中心距离为r,车轮半径为R。-The trajectory of the bicycle wheel accessories. Road surface as a smooth curve f (x), and accessories from wheel center distance r, the wheel radius R
SharifPWE_BZplot
- The ouput is the TE/TM band structure (first five bands) along pricipal directions (G-X-M-G) of a square-lattice photonic crystal with unit cell consisting of a substrate of "epb" relative permittivity with circular rods(holes) of "epa" rel
WSN
- 边长为L的正矩形范围内随机分布N个无线结点，每个结点辐射半径为R，最后连接结点间距离D<R的所有结点。-length of L positive rectangular range randomly distributed N nodes, each node radiation radius is R, and finally connect distance between two nodes D < R .
BEM_FOR_MATLAB
- 边界元测量垂直接地极地表电势的MATLAB程序垂直接地极半径r=0.05m，长度l=0.5m,垂直接地极上电位V0=30V,边界元法求解径向向外8个点的电势.-Boundary element potential measuring vertical ground Polar table MATLAB program vertical ground electrode radius r = 0.05m, length l = 0.5m, the vertical grounding on
20090322
- 一、算法伪码： 1、初始化： 1.1每一个空间的点映射到二维窗格，每个空间的点分配唯一的二维窗格坐标。一个窗格只能有一个点。 1.2为每一只蚂蚁在二维窗格分配唯一的地址 （第一步需要注意的是：空间上点的位置和平面窗格上点的位置完全是两回事，空间上两个点的位置来计算两点之间的距离；而平面上点的位置，主要是用来确定半径为S的区域内的点，计算两个点的空间距离，进而计算群体相似度，最后通过群体相似度来计算拾起或者放下的概率） 2、迭代tmax次 3、所有的蚂蚁运动一次