搜索资源列表
L298_control_Motor
- 该文件包含电机驱动芯片L298的详细应用原理说明和电路。-Motor Driver IC L298 detailed descr iption and application of the principle circuit.
PWM-SPEED-C-PROJECT-
- AT89C51 单片机L298驱动电机，控制2个12V 直流电机。求PWM 调速的C程序，电路图，电机正反转C程序，流程图-AT89C51 microcontroller L298 drive motor, control two 12V DC motors. PWM speed control of C seeking procedures, schematics, motor reversing C program, flow chart
Stepper_Motor.rar
- stepper motor using l298 and MCU Atmega16,stepper motor using l298 and MCU Atmega16
solarbotics_-l298_schematic[2]
- 国外网站上的L298应用的电路图，测试过，可以直接用-L298 abroad site application circuit diagrams, test, and can be directly used
l298
- this a helpful source code -this is a helpful source code
pwm
- 直流电机驱动芯片采用Ｌ２９８．支流电机驱动就是利用ＰＷＭ脉宽控制Ｌ２９８电流输出大小，从而达到控制电机的目的-Motor Driver IC using L298. Tributaries is the use of motor-driven PWM pulse width control L298 current output size, so as to achieve the purpose of the electrical control-DC motor driver chip L2
l298-4A
- Esete es un pirometro con lcd en ccs-Esete es un pirometro con lcd en ccs
vbRobot_Source-code
- this a robot by At89C2051 and control in visual basic, The source code is asm code & frequnce test is in 315MHZ,drive 2 motor dc by l298.enjoy!
eagle-l297-l298
- L298 & L297 eagle design
moteur-pas-a-pas-unipolaire
- stepper motor command with th famous circuit l297 and l298 tested and validated in tunisia
moto
- 键盘控制直流电机正、反转程序，P2.2至P2.6接5个对地键，作为：顺时针、逆时针、停止、加速和减速按键。 P1.0、P1.1接L298的IN1、IN2。P1.2接EN，也就是PWM输出口。 -Keyboard to control DC motor, reverse the process, P2.2 to P2.6 received five pairs of ground key as: clockwise, counterclockwise, stop, acceleration a
ISIS--l297-with-l29.DSN
- desin of l298 l297 for steper motor
speeter-motor
- 本文讲述了细分驱动技术的原理，重点介绍了细分驱动控制系统的设计方法，设计了一套传统细分驱动系统的设计方案，在此基础上，本文进一步介绍了L297、L298两块芯片，采用这两块芯片构成步进电机的驱动电路，应用DAC0832实现D/A转换，采用精简指令集单片机AVR作为脉冲产生器，对步进电机的工作过程进行控制，最终组成电机细分数可选的驱动控制系统。-failed to translate
Microcontroller-PWM-process
- 如果用全桥控制的话，自己搭起来的最好有一个使能控制端，像L293,L298可以从使能端输入PWM信号进行调速，剩下的可以控制正转，反转。-If you use full-bridge control, then take up their best to have an enable control side, as L293, L298 can enable input PWM signal for speed, and the rest can control forward and rev
DVB2.0A
- DVB2.0A is pictures of the mask to make stepper motor driver L297 L298 with the components list . high resolution picture
Module1-1(DriverPMotor)
- start dc motor with driver l298
基于51单片机直流电驱动设计
- 本设计是以单片机AT89S52和L298控制的直流电机脉宽调制调速系统。利用AT89S52芯片进行低成本直流电动机控制系统的设计，能够简化系统构成、降低系统成本、增强系统性能、满足更多应用场合的需要。系统实现对电机的正转、反转、急停、加速、减速的控制，以及PWM的占空比在LCD上的实时显示