资源列表
dsfs
- 扫描信号从C3 ～C0送入,信号依序为1000 ->0100 ->0010 -> 0001->1000 循环,当扫描信号为1000时,则扫描第0行中的四个按键. 扫描信号为0100时,则扫描第1行中的四个按键, 以此类推.如果有按键被按下,则R3～R0的输出信号中会有一个为1,但我们还是是无法确定哪一个键被按下,必須要从R3 ～R0 的输出信号与C3～C0的-scan signal from C0 to C3 into the signal in order of 100
文档22
- ISD4000语音与89C51单片机源程序 -ISD4000 voice and 89C51 source
21IC ARM微控制器LPC210X的LCD接口技术
- 摘要：本文分别以GPI0口直接连接、串行转换连接、CPLD分部连接三种方法阐述了无外部总线的Philips ARM微控制器LPC210X与点阵图形液晶显示器的接口设计，并给出硬件电路框图和主要程序。 -Abstract : GPI0 I were to directly connect a serial link, connecting CPLD Division three methods described without external bus Philips LPC210X ARM
ZLG7289
- 周立功公司芯片ZLG7289键盘和显示芯片的源程序,包括该芯片的各个功能部分的源代码.-weeks meritorious chips ZLG7289 keyboard and display the source code of chips, including the chip all the functional part of the source code.
GPIB-sample
- 一个对GPIB 读写操作的程序源码 LABWINDOW/CVI-write procedures source LABWINDOW / CVI
THREAD00
- 神经网络模拟系统和多任务应用系统开发的C语言源程序-neural network simulation system and multi-tasking application development, the C language source
BCCOR00
- 多任务操作系统控制的DOS环境下的实现的C语言源程序。 利用时间片的方式，多个程序在DOS下并行运行。-multi-task control of the DOS operating system environment on the realization of the C language source code. The use of time unit, a number of procedures under the DOS operating in parallel.
SVGADIB
- MSC或BC开发的SVGA图形开发库(允许使用300x200,640x480,80x600,1024x768等多种模式) 此开发库特别适合嵌入式系统-MSC or the development of the SVGA graphics development library (allowing the use of 300x200, 640x480, 80x600, and other 1024 model) is particularly suited for the developme
51信号
- 由于RTX51 Tiny不支持信号量，本文档编写个事件信号量来RTX51 Tiny实现信号量的操作，-RTX51 not support volume signals, the document prepared incident signal volume RTX51 Tiny signal of operation,
UCOS2中文手册
- 系统的讲解了ucos2，得每个程序都进行了分析，适用于8/16单片机开发-This book systematically introduce the ucos2 ,and analyse every program in the book ,It applies the 8/16 bit singlechip computer development
51uip
- 本文分析了uIP协议栈的结构和应用接口，并讨论了如何将其应用到51系列单片机上。 -Application of ulP This paper analyzes the structure of the protocol stack and application interface, and to discuss how to apply it to the 51 MCU.
点阵图形液晶驱动程序，采用模拟时序接法和编程
- 点阵图形液晶驱动程序，采用模拟时序接法和编程.全面的程序。-dot matrix LCD graphics drivers, analog sequential access method and programming. Comprehensive procedures.