搜索资源列表
chengjichaxun
- 本程序是利用matlab实现gui的实例程序，完成了一个成绩查询系统，读取的文件是xls格式。-This procedure is to use gui example matlab program to achieve complete results of a query system, read the file is xls format.
gyb
- 扩频原理图用于做扩频通信使用，此图是基于matlab的原理图-spread spectrum diagram for the use of spread spectrum communication so that this map is based on the diagram Matlab
conv_encode
- 本设计是一个基于FPGA的咬尾卷积码编码器设计，要求使用verilog语言编写编码器模块，通过编译和综合，并通过matlab和modelsim仿真对比验证设计结果。-The design is an FPGA-based tail-biting convolutional code encoder design requires the use verilog language encoder module, through compilation and synthesis, and by c
fir_verilog_matlab
- 本设计是基于FPGA的一个FIR低通滤波器设计，要求使用Verilog语言编写滤波器模块，通过编译和综合，并通过Matlab和modelsim联合仿真验证设计结果。-This design is a FIR low-pass filter design based on FPGA, use Verilog to program filter module, and joint simulation by Matlab and modelsim to validate the design re
TPCA
- 人脸识别中TensorPCA算法的matlab程序，使用最近邻分类器进行识别。-Face Recognition TensorPCA algorithm matlab procedures, the use of nearest neighbor classifier to identify.
drawn1
- 用matlab读取txt文件然后画图，只需改变文件路径就可用-Read drawing using matlab txt file and then just change the file path can use
ch.2
- 2第二章，主要介绍使用常用的MATLAB命令来处理数据，所提供的代码已经在基于MATLAB7.01环境下编程通过。-the chapter two is only designed for those who use commands in Matlab and tell u how to use these commands.
chengjichaxun
- 本程序是利用matlab实现gui的实例程序，完成了一个成绩查询系统，读取的文件是xls格式。-This procedure is to use gui example matlab program to achieve complete results of a query system, read the file is xls format.
gyb
- 扩频原理图用于做扩频通信使用，此图是基于matlab的原理图-spread spectrum diagram for the use of spread spectrum communication so that this map is based on the diagram Matlab
2833x_FIR
- TI提供的F28335浮点库使用例程，使用FIR实现滤波，结合MATLAB编程。-TI provides F28335 floating-point library routines use, the use of FIR filters achieve, combined with MATLAB programming.
image-rotation
- 基于FPGA的system generator的图像旋转处理，利用system generator的图像旋转处理程序。本程序是基于system generator下的matlab运行。-FPGA-based image processing system generator rotation, the use of image rotation system generator handler. This procedure is based on matlab run under the sy
Scope
- 单片机MSP430实现示波器功能，有相应的MATLAB上位机配合使用，亲测可用。-MCU MSP430 to achieve the oscilloscope function, there is a corresponding MATLAB PC with the use of pro test can be used.
fre_dev_v0.1
- 用verilog编写的频率可以控制的三角函数发生器,其中用matlab编写的sine表存入rom中-use verilog making the generator of sine and cosine
CODE
- 使用的开发环境为matlab，本程序主要用于处理雷达采集到的数据，从而测量车辆等的速度，有很大的现实意义-Use the development environment of matlab, this procedure is mainly used for processing radar data collected, thus measuring the speed of vehicle and so on, have great practical significance
FPGA-design-and-verification-using-Simulink
- Xilinx System Generator for DSP is a MATLAB Simulink block set that facilitates system design. Targeting Xilinx FPGAs within the familiar MATLAB environment, System Generator for DSP gives you the ability to functionally simulate a design and use
Conventional OFDM Synthetic Aperture Radar
- this is matlab code simulate the use of an orthogonal frequency division multiplexing for Synthetic Aperture Radar imaging
DCMotorPIDControl
- 直流电机PID控制，集成电流采样。与本人上传的另一份PID调试软件（matlab编写）配合使用可以达到高效快速的PID参数整定，本带啊结构清晰，简单易懂。-DC motor PID control, integrated current samples. And I uploaded another PID debugging software (matlab write) can be achieved with the use of fast and efficient PID parame
ScomTest
- 串口接收GUI(可实时观察数据图像)：使用方法 我把STM32 工程里的USER文件放进来了 整个工程太大放不下 连接STM32 ADC1 通道15到外设 把USART1接到电脑上 (程序中在DMA中断发送数据帧头) Matlab 打开GUI serial_communication2 ‘打开串口’ OK 看看数据吧 （有时可能会Matlab报错 关闭再重新执行一次GUI 这BUG一直不知道错在哪）-A serial port receives the GUI can be real-
Desktop
- 移相全桥电路零电压开关PWM电路的MATLAB仿真模型，使用MATLAB2012b版本进行仿真。-Phase-shifted full-bridge circuit zero-voltage switch PWM circuit MATLAB simulation model, the use of MATLAB2012b version of the simulation.
FFT64DIF
- 实现64点的快速傅里叶运算，并用modelsim、matlab仿真。(Achieve fast Fourier operations at 64 points, and use Modelsim, matlab simulation.)