搜索资源列表
singlechip
- 139个单片机源代码程序和仿真图（DSN），用proteus仿真，学习单片机绝佳的程序。例如：《lcd1602仿真实例》、2io5键盘模拟音量数码管显示、4线步进电机控制、8通道自动温度检测系统仿真（含原程序）、32X16LED汉字点阵显示屏(atmega16)、32x16汉字、DS18B20仿真实例、PWM电机正反转、PWM调温、SPI演示文件两个595对接、ULN2803、播放音乐、代码大全中文版[1]、单片机控制的电动自行车驱动系统、单片机实验29个、俄罗斯方块、刚做好的十个字的led屏模
line
- This Project Line Following Autonomous Robot is based on 8 bit Microcontroller AT89C2051. This Robot follows the black line which is drawn over the white surface or it follows the white line which is drawn over the black surface. The infrared sensors
debussy53
- Ultimate CRC is a CRC generator/checker. Using generics the core can be fully customized. It creates a function of the data input and the CRC register using XOR-logic. Although the levels of logic gets very high for wide data inputs, the throughput s
files(sunbinseeker@163.com)
- 本文件绝对原创！内附源代码与流程图，介绍MSP430F149通过与型号为XY15M的GPS模块间的RS232通讯，读取其其经纬度信息并进行滤波，同时经过另一个Rs232口输出给PC机。-This files is absolutely created by current author! there are c code and flow chart！ It introduces that the MCU of MSP430F449 communicates with GPS of XY15M
mywork
- 此程序通过MSP430控制四相步进电机实现爬行车的移动，同时可通过红外遥控对单片机下达命令。-This program contorl four-phase stepper motor of crawling cars moving through MSP430, while the microcontroller gets orders through the infrared remote control.
adfmreceiver
- The design of the All Digital FM Receiver circuit in this project uses Phase Locked Loop (PLL) as the main core. The task of the PLL is to maintain coherence between the input (modulated) signal frequency,iωand the respective output frequency,oωvia p
complementary-filter
- 将加速度传感器得到的倾角值和陀螺仪得到角加速度值通过互补滤波程序得到稳定正确的倾角值-Will the dip Angle acceleration sensor get value and the gyroscope get Angle acceleration value through the complementary filter program gets the right Angle stable value
DS18B20
- DS18B20通过串口采集温度，里面有注释能让初学者熟悉整个过程-DS18B20 Demo gets the temperature through serial port.which lets you know about the principle of DS18B20.
PWM-LED
- AT89S52+TX-1C,PWM输出，2按键加减，当占空比达到最高，最低时，2LED亮起指示-AT89S52+TX-1C board,output PWM,use 2 buttons add or minus DutyCycle,2 LEDs will be on when the DutyCycle gets the max or the min
yige-led-shan-shuo-
- 一个led灯的闪烁程序，用单片机控制，很实用，入门者必学。很好用，很简单，用c语言编程。-One led lights flashing procedures, MCU control, very practical, entry gets learn. Very good, very simple, with c programming language.
qiangdaqi
- 获取信号后经过单片机分析，然后给数码管显示最终判断出谁先抢答-Gets the signal after chip analysis, and then to the digital tube display ultimately determine who first responder
VxWorks_watch_dog
- 随着嵌入式电子产品越来越多的应用，实时性操作系统VxWorks得到广泛应用，而定时器正是实时性操作 系统中不可或缺的重要组件。-As the development of embedded electronic products, the RTOS VxWorks gets wide application, and timer is an indispensable important component in RTOS. Based on the VxWorks Watch Dog
STM32F103RC-MPU6050
- STM32F103RC I2C读取MPU6050至上位机超级终端显示实验-stm32f103rc gets data mpu6050 through iic and put it on Hyper Terminal
气压检测
- 通过气压计BMP180 得到数据在串口上传(The barometer BMP180 gets the data)
basicsensor.tar
- a basic program to read from the sensors over i2c. I looked at the source code for RTIMULibDrive11 and the datasheets for HTS221 and LPS25H to build the program. Here is the source code for anyone interested (very simple but it gets the job done).
STM32_HID
- 1，将STM32的USB枚举为HID设备。 2，STM32使用3个端点，端点0用于枚举用，端点1和2用于数据的发送和接收。 3，端点长度为64，也就是单次最多可以传输64个字节数据。 4，STM32获取上位机下发的数据并将该数据通过USB原样返回，同时将数据打印输出。 5，上位机程序通过调用windows的API实现对HID设备的读写控制。(1, the STM32's USB is enumerated as a HID device. 2, STM32 uses 3 endpo
获取系统时间
- 倍福Beckhoff TWINCAT2 获取系统时间功能块(Beckhoff TWINCAT2 gets the system time function block.)
直流电机速度PID控制
- 光电编码器测得的电机速度反馈信号反馈到单片机中。电机设定速度由ZLG7289模块获得，通过SPI通信传输给单片机。单片机系统根据给定的转速与反馈回来的实际速度相减得出偏差，经过控制算法得出控制量。单片机再把控制量以PWM的形式输出，经过L298功率放大驱动直流电机。ZLG7289模块主要用于显示当前直流电机实际转速和给定转速，并让用户通过键盘输入设定速度。(The motor speed feedback signal measured by the photoelectric encoder