搜索资源列表
VHDL范例
- 最高优先级编码器 8位相等比较器 三人表决器(三种不同的描述方式) 加法器描述 8位总线收发器:74245 (注2) 地址译码(for m68008) 多路选择器(使用select语句) LED七段译码 多路选择器(使用if-else语句) 双2-4译码器:74139 多路选择器(使用when-else语句) 二进制到BCD码转换 多路选择器 (使用case语句) 二进制到格雷码转换 双向总线(注2) 汉明纠错吗译码器 三态总线(注2) 汉明纠错吗
BCDADD
- 本程序完成多个BCD码加法,并完成到十进制裁转换-completion of the procedures BCD adder, and complete the conversion to decimal Conference
Low-power
- 1.通过键盘、LCD来进行超低功耗实验 2 在一段时间内,如果用户没有进行按键操作,系统将进入“睡眠”--低功耗状态 3 用户按键后,系统从低功耗状态转到正常的工作状态 4 在非低功耗状态下,程序接收键盘按键执行加法器操作(因为键盘和LCD限制不能实现复杂 5 的功能,如乘法、减法、除法等).-1. Through the keyboard, LCD for ultra low-power experiment 2 over a period of time, if the us
xhjz
- protel99se格式的,信号加载调理电路,用与防止信号加载时短路,原理参加加法电路设计-protel99se format, the signal conditioning circuit load, the load signal and to prevent short circuit, the principle of participation in the design of adder circuit
adder
- 一位BCD码加法器的实现,所得结果大于9或进位位1则加6-A BCD code adder implementation, the result is greater than 9 or carry an additional 6-bit
adder
- 实验一 1位全加器的设计 详细的试验步骤一节过程分析!-Experiment-1 adder design a detailed process analysis of test steps!
Case_Study_FA
- This document objective is to design a one bit full adder to be used as part of a serial adder.-This document objective is to design a one bit full adder to be used as part of a serial adder.
Advanced_Adders
- Advanced topic on adders including: Carry Look Ahead Adder, Binary Parallel Adder/Subtractor, BCD adder circuit, Binary mutiplier circuit.
VLSI_Advanced_CSA
- Advanced VLSI Design on Carry Save Adder Implementation
adder
- 通过四个半加器的互联,来实现四位加法器的电路结构-Through the interconnection of four and a half adder to achieve the four adder circuit
OrCAD15-7DemoTutorial
- Good tutorial in Orcad Capture and Orcad PCB designer including creation of full adder step by step.
test
- 利用AT89S52开关控制由运放构成的加法器,实现输出电压是输入电压的0.1到1.5倍-Using AT89S52 switch constituted by the adder op amp, the output voltage is the input voltage of 0.1 to 1.5 times
ADDER
- .采用原理图输入法和文本输入法实现全减器,分层设计,底层由半加器(也用原理图输入法)和逻辑门组成; 2.给出此项设计的仿真波形; 3.选择实验电路进行验证, 由发光管指示显示结果。 -. The use of schematic and text input method input method to achieve full subtracter, hierarchical design, the bottom of the half adder (also used schem
12
- floating point adder
plus
- 该程序的功能时利用单片机和与非门模拟全加器的功能-The program' s function simulation of microcontroller and NAND gate full adder function
Lantern
- 做个15路输出的彩灯,使用P0.0~P0.7和P2.0~P2.6端口输出;预置数为15个1(10进制32767)。 设置+1(P3.3)和-1(P3.4)两个按钮。 可以减到十进制32047,到32047后如果继续按-1按钮,可以回到32767重新进行减法。 加法也一样,加到32767后,再按+1按钮可以到32047重新+1. 再设置一个按钮(P2.7),当P2.7接地时,在当前显示的数字上减去十进制数1712进行显示。 -Lantern to be a 15-way
Binary-adder-microcontroller-C
- 51单片机 程序驱动P1口 P1口二极管共阳接法 点亮顺出为显示二进制加法 单片机C语言-Binary adder microcontroller C language
LjkBCDPlus
- 自己编写的BCD码加法算法,支持4个字节的数组的BCD运算,如需更多字节,更改for循环控制即可;数据高位放在低地址-Own the BCD adder write algorithm, support 4-byte array BCD arithmetic, high on the low address data more bytes, change the for loop control can be
adder
- 实现一个4位二进制数加法器,实验时用高低电平开关作为输入,用发光二极管管作为输出。-A 4-bit binary adder, experiments with high and low level switch as an input, as output light emitting diode tube.
MCU_51_LED02_C
- 51单片机二进制加法LED显示演示程序C版, 基于HC6800EM3单片机实验板.-51 single-chip the binary adder LED display demo version C, HC6800EM3-based micro-controller board.