搜索资源列表
TG12232E
- 我刚写的TG12232E的测试程序,V0的电压很重要,要接个电位器仔细调节-I just wrote TG12232E testing procedures, the voltage V0 is very important, access to a carefully adjusting potentiometer
ds1805.rar
- 12位的数字电位器,在参加电子设计大赛的时候用的. ,12 digital potentiometer, participating in electronic design contest when used.
x9c102.rar
- 通过AD值调节x9c102数字电位器的电阻值的大小，可以用来作为音量自动调节器的部分源程序。,AD value adjusted by x9c102 digital potentiometer resistance value of the size, can be used as part of the device automatically adjust the volume source.
tlc549
- tlc549A/D转换，电位器调整得到一个0-5V的电压，A/D转换后，利用数码管显示，精确到小数点后两位-tlc549A/D conversion, to get a potentiometer to adjust the voltage 0-5V, A/D conversion, the use of digital display, accurate to two decimal places
AD_generator
- 用MSP430 launch pad制作一个简易的方波信号发生器，要求： 使用MSP430的Timer_A产生方波信号，方波信号频率范围：1KHz~10KHz 方波信号的频率由外部电压控制，电压范围为0-2V，输入电压和输出频率呈线性关系； 外部电压信号由MSP430的片内A/D采集； 外部输入电压由电位器产生； 输出信号的频率误差<10Hz； 系统上电以后默认输出方波信号1kHz。 增加按键控制功能，当S2（P1.3)按下时，通过改变外部输入电压可控制方波信
Digitalpotentiometer
- 基于AD8402的数字电位器，可以拟补模拟电位器进度不够的缺陷，从而提高系统的精度-AD8402 based on the digital potentiometer, can fill to simulate the defects, schedule enough potential to improve precision of the system
x9c103
- 本程序是基于51单片机的数字电位器的衰减，将三个数字电位器串着集连，可以步进一万份！-This procedure is based on 51 single-chip digital potentiometer decay, the three sets of string digital potentiometer connected, you can step ten thousand copies!
X9241
- 音响数字电位器 X9241 C驱动 参考程序 -Audio digital potentiometer X9241 C drive reference program
ad
- 配置单片机的A/D转换器模块，使其对D2区的电位器进行采样，采样结果显示在数码管上。满量程电压为3.3V时，10位A/D的分辨率大约为3mV，由于受噪声影响，A/D采集的数值会出现噪声，尝试添加数字滤波算法，降低噪声的影响。-Configure MCU A/D converter module, so pairs of D2 region potentiometer sampled, the sampling results show that in the digital pipe. Full
MAX5400Drive
- 利用MEGA16中的SPI总线实现对数控电位器MAX5400的控制，每写入一个新的值便可得到一个新的电阻值-The use of the SPI bus MEGA16 achieve MAX5400 digital potentiometer control, each write a new value can be a new resistance value
adda0808
- 可将电位器上的模拟电压变为数字量输出，并显示！-Can be simulated on the potentiometer voltage into a digital output, and display!
ServoPotentiometer
- Controlling Servo with potentiometer ( Atmega 32 )
potentiometer
- control potentiometer to get en pulse output-control potentiometer to get en pulse output
MCUcontrolADN2850
- 通过MCU控制ADN2850来完成对于数字电位器的控制-Through the MCU control ADN2850 to complete control of the digital potentiometer
Test06_ADC
- 对nxp-LCP2478板子上的电位器输入的电压进行AD转化后输出，并在串口段进行监视！- Carries on after on the nxp-LCP2478 board s potentiometer input s voltage AD transforms outputs, and carries on the surveillance in the serial port section!
use-MCU-tocontrol-Potentiometer-
- 数字电位器与单片机接口代码程序，包括电路，数字电位器资料。-the way to use MCU to control potentiometer
Digital-potentiometer-adjustment
- 此程序是基于stc单片机的控制数字电位器MCP41010的程序，并带有protues仿真图。-This procedure is based on stc microcontroller MCP41010 digital potentiometer control procedures, and with protues simulation Fig.
BLDC-6-LOAD-PWM-Speed-Potentiometer
- 用keil4编译的stm32单片机开发的电位器调速的BLDC控制程序-Compiled by keil4 stm32 MCU development of potentiometer speed of BLDC control program
BLDC-3-LOAD-PWM-Speed-Potentiometer
- 用keil4编译的电位器3路调速pwm控制的BLDC控制电路-Keil4 compiled with potentiometer 3-way control BLDC pwm speed control circuit
potentiometer-control-tri-color-LED
- 这是一个用Arduino控制板实现的电位器控制三色LED的灯颜色变化的程序及电路连接图。-This is a Arduino control board potentiometer control to achieve three-color LED light color change procedures and circuit connection diagram.