搜索资源列表
2010.5.11-AD-CAN-LCD
- 此程序是在电子白菜的STM32开发板上实现的，采集电位器模拟量，经过AD转化，然后发送到CAN上-This program is in the electronic cabbage STM32 development board to achieve, capture analog potentiometer, after AD conversion, and then sent to the CAN on the
AD_TEST
- 本文件是AD测试实验；测试前需要对管脚复用的电压基准进行设置，将JP10的2，3脚短接，1脚空出。AD输入端子(J10)可输入4路AD(ADC0--ADC3)，另有1路可测量片内温度，5路采样值都通过串口发送出去，在串口调试助手上看观察其值。4路AD中ADC0可通过跳线器(JP5)“ADJ_VOL”（1，2脚短接）与板上电位器相连，通过手动调VR1可以观察到电压值的变化-This document is the AD test experiment testing is required be
DAshiyan
- 用ADC0809完成模拟信号到数字信号的转换。输入模拟信号由A/D转换单元可调电位器提供的0～5V，输出数字量显示在显示器屏幕上-Complete with the ADC0809 analog to digital signal conversion. Input analog signal by the A/D conversion unit adjustable potentiometer provided 0 ~ 5V, digital output displayed on the m
ADshiyan
- 用ADC0809完成模拟信号到数字信号的转换。输入模拟信号由A/D转换单元可调电位器提供的0～5V，输出数字量显示在显示器屏幕上。显示形式为：AD0809：IN0 XX。 -Complete with the ADC0809 analog to digital signal conversion. Input analog signal by the A/D conversion unit adjustable potentiometer provided 0 ~ 5V, digital out
main
- 通过电位器的两端接地和+5v中间抽头接adc，根据adc读取的值在数码管上显示旋转的角度。-Grounded at both ends of the potentiometer and the+5 v intermediate tap connected to adc, adc read according to the value of the digital display on the angle of rotation.
P4
- msp430 149，模拟输入，电位计连续可调输入，产生PWM。-msp430 149, analog input, continuously adjustable potentiometer input to generate PWM.
F340_ad
- 本程序是对电位器产生的电压值进行采样,可以在寄存器观察AD的 也可以通过LCD将值显示出来-The program is produced by the potentiometer voltage is sampled, can be observed in the AD can also register through the LCD will display the value
Digital-voltmeter
- 数字电压表：利用模数转换芯片ADC0832实现，输入电压经89k电阻和10k精密电位器分压，测试电压为0～51v，可用表校对-Digital voltmeter: the use of analog to digital conversion chip ADC0832 achieved, the input voltage through 89k and 10k resistors precision potentiometer divider, a test voltage of 0 ~ 51
MCP41010yudanpianjiat89c51
- MCP41010与单片机at89c51联合控制LED灯的亮度，数字电位器与单片机联合应用-MCP41010 and microcontroller at89c51 joint control the brightness of the LED lights, digital potentiometer with a microcontroller application
dianweiqi
- 由电位器控制单片机实现无级调温，定时，主要用于电热锅。-Potentiometer control microcontroller stepless thermostat, timer, mainly used for electric pan.
i2c
- i2c运用在数字电位计中，控制数字电位计-i2c used in the digital potentiometer to control the digital potentiometer
ANALOG_READ
- READ AN ANALOG POTENTIOMETER AND EXECUTE AN OUTPUT
Annular-inverted-pendulum
- 这是用飞思卡尔单片机MC9S12XS128实现的一级倒立摆，里面有详细的解释，基本都有注解。 机械上包括：一个直流电机，一个电位器检测摆杆角度，一个两相编码器反馈转角。 软件上采用了四倍化编码器，将原来编码器的1000线，变成了4000线，倒立摆的控制周期定位了10ms，可改，该实验达到了平衡控制的目的，但是并没有完成上甩，需要用手把摆杆放直，然后启动单片机，实验时，单片机在30度内平衡控制，由于所选的电机虚位大，所以控制时抖的厉害。-Freescale microcontrolle
10172
- A/D 功能模拟 从5V电位器接出电压 作为模拟信号-A/D function analog 5V potentiometer connected to a voltage as an analog signal
Potentiometer
- This example shows how to use the ADC peripheral.-This example shows how to use the ADC peripheral to measure the potentionmeter level.
44B0Test
- Descr iption of TFT-LCD-Driver Potentiometer example.-This example shows how to use the TFT-LCD-Driver peripheral to measure the potentionmeter level.
Circuit_02
- Arduino 开源硬件开发板实验代码二 电位计控制LED闪烁频率- Measure the position of a potentiometer and use it to control the blink rate of an LED. Turn the knob to make it blink faster or slower!
fadingLedWithPod
- A simple C file that fades in and out an LED attached to Arduino UNO with the use of a potensiometer. The code is C. The potentiometer has to be attached to analog pin 0 and the LED to digital pin 6. It uses both ADC ( analog to digital conversi
main
- 测量ADC电位器上的电压值，精确到毫伏，结果在串口助手显示-Measurement ADC voltage value on the potentiometer, accurate to millivolts, the results shown in serial assistant
TPL0501
- TI公司的TPL0501数字电位器芯片的驱动源程序代码-TI' s TPL0501 digital potentiometer chip driver source code